LED 3rd Brake Lights Tailgate Rear Lamp for Jeep Wrangler JK JKU 07-17 2 pcs (Red)

The only thing I can say negative is these are NOT plug and play. If you plug them when they will both blink at the same time and not with the r or l blinker. They do provide enough wire to reroute it to the r and l blinker, but that’s not something I would do but my husband knows electrical and cars so he did it himself. They are as bright as our brakes (so not over powering). They fit perfectly in place. I have never seen these before on anyone’s jeep so I love that they are so unique. Honestly idk how much he spent on them, they just showed up. But the work well (now that he re-wired one) no flickering that we have noticed and no electrical issues.

As a running light, brake light and reverse light, this thing is great and only reasonably difficult to install. As a turn signal (which is 1/4 the job) it either blinks both lights, or does nothing. This all depends on which direction you are turning relative to the side the light was installed. If you wired them to the driver's side, then turning left will light up both non-blinking lights. When turning right, no lights come on, with (of course) the exception of your turn signal. This can be remedied by wiring to both lights individually, but alas, the kit does not allow for that. You would have to build your own harness to mimic the provided factory side. I personally didn't bother. All I wanted was a 3rd brake light/running/reverse lights anyway. The lights themselves function fantastically. I wouldn't change a thing. They are good and bright and seem pretty durable. And if you use cable stays, the wires behave nicely. All in all, a good experience. I like them a lot. Great location for 3rd brake light/running/reverse lights on a Jeep.

GOOD: The LED lights themselves are fantastic, the housing, the fit (they click right on). The wiring harness is great and can make it down into the tire well (where the wiring is) if your able to run it through the hard top with the rear wiper/washer lines... BAD: As far as connections: this is NOT plug and play, you have to splice these into the wiring yourself, which is fine if you're ok doing that type of work... UGLY: the 'turn signals' don't actually work properly. they both flash together with whichever side harness you splice them into... this is a serious problem and a major design flaw... since the stock lights use the running lights as a turn signal in DOT vehicles, each sides turn signal/running light is different. You can fix the turn signal issue, if you know what your doing, and want to wire a 5th wire down the harness and run the entire harness into the drivers side. in that wheel well there is the wiring harness for the trailer lights (if you have the trailer package...) you can then splice the proper 5th wire for the passenger side into that wire, and then they would function as proper turn signals... but you should probably know what your doing for that.... so good luck...

Worked great!!!! I only wired in the Brake, Reverse and Turn signal. Did not use them as running lights as I wanted them to stand out when hitting the brakes. Looks like it came from the factory, cant tell it is an aftermarket add-on. Have had the installed for a couple of years and still work well.

Your wiring connection is wrong, white wire is reverse light, green wire is running light, the black and red wire is correct. Once I made the correction all lights work fine.

No instructions! I have the ability to splice the wires but it would be nice if I knew where to splice them.

Read the reviews they will work for stop and reverse. If you want them to function as directionals as well, you will have to cut and run a new wire. It's not that hard. get a T trailer splitter and it will direct connect to the harness on the driver's side rear lamp. Then run it through the grommet where the rear hardtop power supply plug is. I added a 5-pn connector here so I could unplug to remove the hardtop. On the lights, take the wire (I think its red) that runs to the right (passenger) light and snip it at the Y. From here run your new line and tie it into the right lamp terminal on the clip added. Then just hide your wires. Works great

To get them to function properly, I guess you could wire them into the trailer wire harness however, I opted to separate each light by cutting the splice out and wiring them separately to the left and right tail lights. This way, they function properly as running lights, brake lights, turn signals, and reverse lights. I fabricated two pigtails using Delphi connectors so I am able to remove the top, if I chose. Very satisfied with this product thus far!

Great product & good value for money. Functional & added more visibility at night. Highly recommended.

Funciona bien pero los cables no van como lo describe el manual