OverMolded Rubber Grip for CZ 75 Full Size & CZ 85, Black - 75000

I couldn't be any happier with this Hogue grip for my CZ-75B duo-tone. Prior to ordering it, I was a little apprehensive after reading the Amazon reviews mentioning fitment problems, magazine release problems, hand size warnings, etc. So here's my take. I received my package today 2 days early (thanks, Amazon) and the grip probably took all of 60 seconds to install. It didn't interfere at all with my mag release button so it required no trimming. With a trusty flashlight, I could see the interior grip surfaces were fitting perfectly within the frame openings. Thinking I was all done except for the cheering, I attempted to insert an empty magazine. Just as happened to a previous reviewer, it did not want to seat in the frame grip. With a little more force, the mag did install but without the familiar click when fully seated. Upon pushing the mag release, the mag didn't budge and remained completely locked in place. Now, and feeling like the village idiot, I started backing out the two little grip installation screws. After a full reverse turn on each side, the magazine popped right out as it should. Next I tried four empty magazines and each installed and released normally. I didn't feel I had originally installed these screws any tighter than on the CZ factory grips. Everything is working fine and I mention all of this as a heads up for future buyers. As the title of my review states, this grip fit my large hands perfectly. I have long fingers and they fit the finger grooves just right in the grip. I like the feel of the rubber much, much more the the factory grips. The CZ-75 is not a wimpy plastic handgun, it's a heavy, full size, all steel service pistol. IMHO, the Hogue rubber grip is the perfect compliment adding to the already nice balance of this heavyweight.

Fits my cz-75bd tight. Get either side started and screwed down then pull the other side into place. It fits snug.

I've installed Hogue grips on several pistols I've owned over the years. I have always liked the products. This grip is no different. The quality is good and the fit is tight. The grips fit my hand well and are much more comfortable than the factory ones, in my opinion. They are a little thicker than stock, so work well with my big hands. The biggest difference I noticed was the way it molds in to your hand. Shooting 8" plates at 8 yards, I noticed the position of my hands didn't tend to change from shot to shot. The pistol didn't slip and seemed to be one with my strong hand. I read a few complaints where folks complained these grips didn't fit or required modification. I have the CZ 75B and can see what they meant, but they are wrong. The fit is tight and it's made to fit perfectly. The trick is getting one side in place then stretching the grip around to click in on the other side. The grips are each backed with plastic so they remain rigid, but the center (where the finger grooves are) is only rubber and stretches slightly. There are small extrusions that match up with holes on the frame of the pistol perfectly. Get one side in then stretch the grip a bit as you wrap it around to the other side and it will fit in perfectly. It will seem to be pretty firmly attached even before you apply the screws if you've done it correctly. I've been using these now for over 6 months and probably 2500 rounds. They show no obvious signs of wear. Bottom line: I would recommend these to folks looking for the finger groove style of grips. In fact, I have several times.

These grips fit better than the factory grips. The factory grips are a softish palm swell type. There are some noticeable gaps around the grip frame that while it doesn't diminish functionality it's just not neat and clean looking. The Hogue grips fit so perfectly on the frame. The way they blend to the contours was just amazing. I didn't have to heat up the finger grooves at all just a minor bit of pull and I was able to lock in the panels perfectly on each side. These are flat side grip panels so they give your thumb a little more reach on the safety and the slide release. The grip dimensions are perfect for my hands, plus being flat sided it carries better. Outbags makes a nice vegetable tanned holster for the compact CZ 75 type guns. Just wet it stick your gun in it and mold the shape of your gun to it, then pull it out and let it dry. Perfect fit!

Had to buy to replace the broken original plastic grips of a CZ75 (9x19). The grip is very resistent, fits perfectly to the pistol and does not slip, even when wet. In my particular case I found an issue to establish a good grip when quick drawing the gun (in a Weaver variation). I use a concealed pancake holster very close to the body in the waist. I believe that the reasons for this issue were: I was very used to my original grip size, and it got a bit bigger since the Hogue wraps the pistol grip around the front; I was not used to the finger grooves and I feel that they are too prominent for my hand; and since the rubber material sticks very firmly to my hand it was hard to adapt the grip once drawed (holding the pistol). My hands size is 10. I kept my Hogue, but ended up buying another grip that didn't wrap the gun.

Feels great. It is tight fitting, but I found a solution. While it seems like it is too small to reach around, I used a heat gun to warm it and it snapped right into place. Replaced the screw, all done. A hair dryer should also work.

Used these on my CZ-75 SP-01 tactical. After 2 1/2 years the finger grooves have stretched considerably and I can now feel the finger grooves move when I grip or shoot. Now I'll have to replace these. Avoid.

Bought grips for the ASG CZ75 ( co2 ) they fit like a glove, tip for fitting attach one side then warm grips, I used wife's hairdryer, stretch round to other side click into place then put the screw in.

The CZ75 is a good fit with the factory grips, but the Hogue grips make a good thing great! I have used similar Hogue finger grips on 1911 guns and they are just as effective in placing the hand consistently on this pistol. A consistent and sure grip aided my shooting from the first magazine after installation. The grips are a snug fit, but installation is easy and quick. I re-used the factory grip screws and the grip swap took less that 3 minutes. The well defined finger grooves fit my medium sized hands very well. The texture is grippy enough for the casual shooting that I do. Some grip tape on the backstrap would be all that is required for really fast paced shooting with complete control. The grips are a good value and fit well to produce a more enjoyable shooting experience.

Sono riuscito ad adattarle ad una CZ 97B , altro calibro ma pistola molto simile. Fanno fare un figurone e migliorano tantissimo il grip. Basta tirare un po' la gomma con l'aiuto di un phon per adattarle. Se avete una 75 invece sono già adatte così senza modifiche.

Très satisfait produit de qualité. S’adapte parfaitement au Cz shadow sp 01!!! Reçu avant l’heure...

問題なく装着できます