5 Pcs 0.96 Inch OLED I2C IIC Display Module 12864 128x64 Pixel SSD1306 Mini Self-Luminous OLED Screen Board Compatible with Arduino Raspberry Pi(Blue and Yellow)

I use an OpenSprinkler controller to run my yard irrigation system. The controller has an OLED display on the front that shows the status of the system, but over time it gets burned in, making it extremely difficult to read what’s on the screen. These OLED displays that I bought are a drop-in replacement for the one that came with the OpenSprinkler controller, so they are a very cost effective and simple way to restore the OpenSprinkler controller to like-new condition. I opted to go with the blue displays instead of the white ones that would have matched what came with the OpenSprinkler controller, but I’m sure the white ones would work just as well. I’m very happy with the quality of the display… it’s very sharp and easy to read.

I always feel like I'm gambling when I order parts like these. Well, I hit pay dirt with these! All 5 worked flawlessly in my project. I had no issues using them with different Arduino Libraries that are out there. My only issue (and it's pretty small) is that I would have liked the pins to either be not soldered in. As they are now, it's great for the breadboard, but depending on your use, you may find it a little inconvenient. But, since I'm pretty handy with the solder station, I had no problems swapping out the pins to something that better fit my project. Great bonus is the small case each display comes in. I now use those for some small parts.

These are neat little displays for a good price. Was pretty easy to get going on a Raspberry Pi Pico (RP2040). Display is clear and big enough to see text even when the characters are ~2mm high. Build quality seems good enough for a bare PCB; has a 4-pin I2C header and 2mm mounting holes. By default, the device address is 0x3c, but if you are good with a soldering iron, you can move a tiny SMD resistor to change the address to 0x3D; the spot is clearly written on the back of the PCB near the header pins. There was no documentation with the displays, so you are kinda on your own. But, using Circuit Python, and ADAFruit's bootloader and libraries, and then Googling around, I was able to get it working easily enough. I did have to add a couple 4.7kΩ pull-up resistors on the SDA and SCL lines (the little circuit board attached to the display in my pic). Following another reviewer's advice, I powered it by 3.3v from the RPi output. If you need a starting point (like I did), I've attached a picture showing it working and a screenshot of the basic code I used to get it running. There's probably better ways, but this is just what I did. Hopefully, those pics are allowed. If not, you might have to Google around. Just remember to set the GPIO pins for your I2C, device address 0x3c, and the display dimensions (128x64) where needed.

These work just fine if you need a tiny screen for a project. Works with the Adafruit SSD1306 library. They are bright and readable. The second color is the top 16 pixels, 1/4th of the screen.

These worked well with an esp8226 project using the Adafruit library for SSD1306 devices. I have not tested all of them but the two I have tested were as expected.

These are great for integrating output on an Arduino. The documentation and sample code for similar modules makes it easy to implement. It is a simple matter to connect to a network time server and update date and time for example. They are very small, but the design is good and it seems relatively durable. I haven't yet taken the protective film off, but with it on the screen is very clear, responsive, and readable.

I recently purchased the Hosyond 5 Pcs 0.96 Inch OLED I2C Display Modules for a project involving Arduino and Raspberry Pi, and I am delighted with the performance. These compact screens offer excellent readability with crisp blue and yellow displays, making them perfect for adding a visual output to any small-scale electronics project. The 128x64 pixel resolution is quite impressive for their size, and the SSD1306 driver integration provides smooth operation and easy setup. Compatibility with both Arduino and Raspberry Pi enhances their versatility significantly. I found the I2C interface particularly helpful for simplifying connections and saving valuable GPIO pins. Overall, these OLED modules are a great value for their price, offering high performance in a small package. Perfect for anyone looking to add a self-luminous display to their DIY electronics.

Started adding one of these to my projects because I like to see what is happening, simple to integrate and program, so displaying information on the screen is rather easy. I need to order some more because I have all 5 in use and so far no issues with any of them.

5個ともすべて正常に動作しました。 SSD1306の標準仕様に準拠しているようで問題なく動作しました。

Vienen bien protegidas en una caja de plástico cada una. Funcionan como se espera y a precio razonable.

Good quality OLED screens. Tested they will run normally at a voltage as low as 3.5v without any loss of brightness. Each OLED screen is nicely packaged in its own protective little plastic box.

Love It i use it as my 3D printer Mini Screen

Worked great.