PC Products - 128114 PC-11 Two-Part Marine Epoxy Adhesive Paste, Off White, 8 lb in Two Cans

perfect for vertical applications, nice and thick.

I have used this product many times over the years. It is my go-to for repair work needing epoxy. Great product.

PC-11 Marine epoxy is great stuff. This large container is much more affordable than the smaller package. This stuff does not cover a huge area, so make sure you save money and buy this one pound package. It's like the rest, mix 2 together and starts to harden up within minutes. It comes out of the tube thick to begin with, like putty, and so it's EZ to apply, especially to large areas or wide gaps, even upside down - it's going to stay in place until cured. It says 30 min working time, but I was ready to apply after a couple minutes of mixing the 2 together to create a new uniform color, I applied it with a stiff putty knife and did not wait to test the half hour work time. I actually applied a 2nd coat on top of the first because although the majority of leak was fixed with the first application, there was a small dribble because of the awkward location. Wear disposable gloves - this stuff is incredibly super sticky - and I cleaned my stiff putty knife with mineral spirts and rubbing with rag. Allow it cure at least 24 hours. It says it cures under water - did not test it but given how super thick this is, I believe it. Solid as a rock.

I used the Epoxy Adhesive Paste to repair a crack in my countertop, and it worked perfectly. The application was easy, and it set quickly, making it ideal for my DIY project. The only downside was that I needed to mix it beforehand instead of using it pre-mixed. I highly recommend this product!

This product worked great on my water fountain base. There was a 2" hole in the resin, and this completely sealed the whole thing. I also did some hairline fractures with this. It is very very sticky wear gloves. Doesn't smell great. Product arrived fast. Sandable, but in large amounts becomes very hard and built up, so use sparingly in an even proportion.

This stuff works great drive is very hard and does not crack I will buy this again

This stuff is simply amazing. Works great as window caulk, sealing around outdoor cables, patching holes in siding, and many other applications. This holds up while other products from Home Depot will fail within a few years. It's worth the price to use this stuff and not have to worry about it in the future. The only other product that can compete with this stuff is PC Woody. This is easier to work with and lasts forever.

This is the third time I've purchased PC-11 (first time on Amazon). The last two times it came in little metal cans. The plastic containers that are used now are an improvement. But, I found after three uses it does not set up as hard, and bond as hard as the decade old stuff (same stuff PC-11) I just mixed up to compare. The new stuff still works but it does not get rock hard. it gets hard, but I can peel it with a paint scraper. I promise that I prepped the adhesion surfaces properly by sanding and degreasing with acetone (metal bonding to fiberglass was the goal). The bond failed over about a week with gentle stress on it. I cleaned it all up for round two after the initial failure, and used my 10 yr old PC-11 and it is rock solid. I'd love to hear a reply from the manufacturer on this review. I do know epoxy somewhat. I have three kinds in my garage. I occasionally use epoxy and fiberglass powder. I have been very successful in my repairs. PC-11 is not at this time a product I would buy again based on my recent experiences.

Cumple con lo que indican, me sirvió. Buen producto.

Works good but the PC-7 is the better product for gluing soapstone.

Best epoxy I ever used.

Used this pack to fill a crack in a retaining wall that was moving. Wall has not moved in more than year! Ideal where a larger amount of strong adhesive is needed. Bear in mind surface prep as otherwise will fail at the interface.

Ideal for smaller jobs. I used it to fair the leading and trailing edge of a sailboat rudder. I tried another two part putty which was too stiff to smooth with a spatula. After steeing for a day or two, it sands easily, althuogh it would be a lot of work if this was used for a large surface like a boat hull.