4" Inch Smoked Amber LED Front Grille Marker Lights Kit, 4Pcs 4 Inch Amber Full LED Center Grille Grill Running/Position Light Sealed 9 LEDs Pickup Trucks, 4"x1" RV Camper Boat Uitility Strip Bar 12V

Love the smoked look. Very bright. Make sure you buy extra wires.

Haven’t been able to install them yet but they are working fine and they are very easy to install and only require a couple of wires to install. They are very good for a small amount of space on the outside of my truck. They have a good price and they are very durable so I will be happy with them for the job I am going for. They have the best quality of life and they are very easy to install so they will work well for me as long as they have a decent amount of color and not too dull but I will be able to use for my truck so I think they are very good quality and very durable. My brother has a similar style on his truck and they do have a lot of good quality and they use them all of the time. Also they do not come with any instructions for how to install them but I think I can figure that out myself if you would like to send me the instructions for that I would appreciate it thanks again for the help.

Quick and easy install, put this on my 2022 Jeep gladiator I did have to modify the plastic Housing a bit by cutting some of it but other than that the install was quick and the quality of the lighting is fantastic

Easy to install, look great and they are smoked. I prefer the thinner, straight with hard edges look compared to the bubble look or the rounded ones. Only issue is that they will at times get leaks and once that happens the LED's will stop working. I found that covering the backs with an all weather silicone prevents this from happening. I have been through two sets to finally come to this conclusion. My second set has been running strong for the last 2 years.

Easy install and they look great. Can't beat the price, will see how long they last.

One review says wires are thin, but better than many I've bought. Seemed to be well made and very bright, as they show up even during the day. Down side is that they come with screws that are not stainless and installed on a vehicle, that would mean instant rust. I switched them out for some stainless screws to install in my grill. I wanted to mount them to a horizontal part of the grill, so I used 1 x 1 aluminum angle brackets to grill bars and then attached lights to those. Very happy with the lights for the price.

There’s literally no pictures/reviews/info on grill lights for the 5th Gen Rams. After lots of searching, reading, videoing watching, I decided to give these a whirl. I have no idea on the longevity of these, but for the amount of work to get these in for, hopefully they last. I installed/soldered these on 2 lines, pos and neg. I protected the wire with loom and ran the wire to the drivers side. I have jumper harnesses to “splice” into so I don’t have to hack up the oem wires. The parking light wire is the white/colored wire that’s the only one on that row of the harness, the other 3 positives/white/colored for headlights, brights, and turn signals are in the other row. I used the black/neg wire right next to the parking white wire for the neg side. For mounting, remove the whole grille. You can mount them in the flat slats above/below the row I mounted them in from the front, with tension only. But you’d have to try and make the connections behind, which will be sloppy and look like trash. Pull the grille like I did and do it the right way. There’s YouTube’s on how to pull the grille.Also, pull both layers of the grille apart so you can more easily access the front main grille, this is straightforward. I ran the wire/loom through a drilled hole as pictured on the drivers side. This brings the harness right near the headlight harness. As to mounting, I decided to do the oval openings for slightly more concealment when off. That’ll help hide the dead areas on each side of the light. The lights were installed with 3m heavy duty double sided tape (grey stuff). I lined up where the light should be and ran the light in along the top side, as there’s enough room to get it in there with the other side of the tape removed so it sticks. Once in place, push/squeeze down to set in place. Clean both the light and mounting surface with alcohol for best bonding. Like I said, for the amount of work to pull the grille and mount these, hopefully they last.

Very good all around option.

オシャレで気に入ってます バエ最高

جيد جدا يستحق الشراء

Purchased these lights for my 2024 Tundra a year ago and looks great. Great product, no issues.

デリカD5後期に取り付けしました。 グリルに配線用の穴を明け、本体とグリルは両面テープでくっつけ、バッテリーから電源を取りました。上や横から見ると少し飛び出している感じはありますが、特に問題はないと思います。 洗車時は気をつける必要があるかと思いますが、特に今は取れそうな感じはないので耐久は様子見です。本体の防水加工ですが、一応中の部分は処理されているかなという印象ですが、本体と側の部分はパカパカ取れるので、ホームセンターで売っているセメダインsuper XGで外れないように処理をしました。 説明書はないですが値段も安く、グリルマーカーもそこそこ大きいのでインパクトはあると思います。

Very simple and easy fitting.