Junction Box, Electrical Box IP65 Water Resistant Dustproof ABS Plastic Project Enclosure for Electronics White, External Size 5.9 x 4.3 x 2.8 inch

I got this box to install a POE security camera for the house, I wanted the camera to be attached to the box in order to hide some of the excess cable that came with the box. Overall this box was exactly what I wanted for my project, it is pretty durable for being plastic and the box comes with everything needed to mount and run at least 2 cables out of it (I only needed 1). The craftsmanship of the box is really good, quite exceeding my expectations for the price, I would definitely recommend this to anyone who is in need of a product like this. There is one thing I think could be improved with this box. As I've mentioned earlier I bought this to mount a POE security camera, while I loved that this box came with 1/2" cable glands but the outside cap of the glands is just a TAD too small for a standard RJ45 connector (even without any sleeves) to go through. It is an easy fix where I just used a step drill bit to make the cap a bit bigger but after getting the cable through even when screwed all the way in there is still a little bit of space between the cable and the gland seal. I don't know if it is because I made the cap bigger but luckily where I mounted the box isn't be exposed to weather. Maybe this box isn't designed to have a CAT5 cable run through the gland but with POE stuff being very popular these days I think the manufacturer should take that into consideration.

Size of box reviewed: 5.9 x 5.9 x 2.8 (150mm x 150mm x 70mm). I found the material of the box allowed for easy modifications with needed holes to be drilled. The lid fits nicely on the box, with a built-in seal around the edge to keep it weatherproof. Overall, I was very pleased with the quality of workmanship and material of this project box. My project required several holes to be drilled in my box. The pre-scored 1" (25 mm) knock-outs are nice, but I needed a 1-1/8" (28 mm) hole where two of those knock-outs were located. So, I drilled a small pilot hole in the center of the knock-outs and then used a hole-saw attachment on my drill to bore the required 1-1/8" (28mm) hole (see pic with yellow hole saw). My project was to supply and distribute multiple voltages to be used by different devices. I mounted 2 ScanStrut weatherproof USB-A ports (ASIN B071WXWS9C) on the sides of the box. Inside the box, I also mounted a 6 VDC buck converter (ASIN B07SGJSLDL) and a 12 VDC buck/boost converter (ASIN B07N3QT628). From each of these converters, I will route the outputs through the cable glands mounted on the top of the box. The LeMotech box comes with 2 black cable glands, but I used 2 grey ones (ASIN B094ZDSD86) instead of the ones that came with the box. These required 2 custom 12 mm holes to be drilled in the top side of the box.. This has turned out to be one of the smoothest project box jobs I have done. Hints for good results: drill holes slowly into the material, and do NOT force the drill/saw into the material. When sawing, proceed slowly so as to CUT the material, rather than BURN it. Since this project, I have ordered another one of the boxes of this same size, as well as another in a smaller size, for use in other projects.

Great box and good seal

Good project box. It fits a 120mm fan (I cut a hole in the top). It’s housing an SKR E3 mini with plenty of space. The material is easy enough to heat set standoffs. The price is okay, but the flanges are a little small for my use.

This is a replacement for one that I have had in use for several years. The caulking around a project hole wore out and caused a leak, so a replacement was needed. It houses a water sensor for my pond fountain that turns off the fountain when water level drops too low. My only complaint is the screws holding the box together rusted together so I had to drill them out which damaged the box. Otherwise, this is a good product and worth the money. I am going back together with stainless steel screws just in case!

yes seems to work pretty good

the knockout holes are for 3/4" not 1/2". You will need to buy reducing washers for the included fittings. still overall it is a good product and a good price.

I used two of the boxes under the exposed area under my back porch. They are visible. So the had to look good, and do their job, on both accounts...perfect, great looking, extremely well made. Worth every penny!