Creality Official Ender 3 S1 Heating Block Kit, Sprite Extruder Upgrade Heater Block Kit High Temperature 300℃ Titanium Heatbreak Plated Copper Nozzle for Ender3 S1 Pro, CR10 Smart Pro,Ender 3 S1 Plus

Since upgrading to this direct extruder I've had such better printing results. Takes a little bit of time to install but the overall result is much better. Would reccomend

Bought this to replace the original creality bowden extruder hotend. Good instructions with videos online. Small amount of plug swaps on the control board to remove old hotend wiring and plug new in. No need to update firmware so pretty easy job if your happy changing the wiring. Direct drive so much easier to use for filament swaps and you can use all the small lengths of filament that were too short to go through bowden tube. Wish I'd made the switch earlier

Related to C-high temp.First of all, it comes with larger nozzle, there is no description and there is no marking on nozzle so you will get horrible prints with 0.4 settings. it's not 0.4. I guess it's 0.5-0.6. And yes it does not come with secure bolt as in original Sprite that comes with printer out of box, but heater is secured with another small screw from the bottom, only thermistor itself is secured with white composite. I am happy with purchase, it melts plastic much easier. 4 stars for no propper description and a high price. And in overall Sprite extruder is ok, but plastic used is very poor.

I bought by mistake thinking it would fit Ender 3 V3 SE 'Sprite'. This is for the proper Sprite and and it doesn't truly fit the cheap 'Sprite' that comes with the Ender 3 V3 SE. Thermistor connection it too teeny. Had no choice so had to use existing thermistor which hung out by at least 15mm but it's still going now.

Its hard to review this as i have put it on a printer that it isnt intended for, i have added it it to my Mk1 Ender 3 Pro, i have already upgraded the main-board, the head works well but i cant use the bed leveling as the CR Touch is positioned so far to the front left that it misses the bed, firmware (Ender V2) alterations could solve this but it works so ill leave it as is with manual bed leveling, print quality is good and being direct drive printing TPU is easy.

Bought this as my sprite pro had died an untimely death and I needed to get fixed fairly quick. Connected this to my s1 pro and everything was fine until I tried to print. The filament was not feeding in. Turns out this new £92 unit had a broken wire going to the motherboard and this was the one that powered the motor. The cure would be to contact ceality and wait for a new wire to arrive. Not good when I splashed out on a new extruder to expedite stuff. My solution. Return to ebay for a refund and buy elsewhere

I used this on my heavily modded Ender 3. Was easy to install, everything worked just fine. All I did was adjust the part cooling fan as it was placed a bit to high and I wanted it closer to the nozzle.Also when ordering I was confused if it came with the CR touch ribbon cable. But to my surprise in the box there was a cable for the CR-Touch! So I guess you do get it after all.Very happy with the performance and quality. I can print TPU much faster and I get very little stringing compared to by boden setup.Definitely would recommend this upgrade.

Upgrade for my S1, it was easy to fit. The power cable is stiff and found plugging it in first then installing it into the machine was the way to go

Works as described. I used the old belt to measure how much was needed and cut. The bushings were no problem, just used some pliers to squeeze / fold it, and we're back in business. There's enough for another repair as well. It comes with 6 bushings, but the extra 2 must be too redo a set of you need to, no way you get three repairs out of this since the belt isn't long enough. Overall, highly recommend.

Ho installato l'Estrusore Pro Dual Gear Feeding di Creality sulla mia stampante Ender 3 Pro con la scheda 4.2.7, e devo dire che complessivamente sono soddisfatto delle sue prestazioni.Innanzitutto, devo sottolineare che questo estrusore non è adatto per la stampa ad alta velocità, quindi se stai cercando di accelerare il processo di stampa, potresti essere deluso. Tuttavia, l'Estrusore Pro offre una presa del filamento eccellente e si è dimostrato molto efficace anche con materiali flessibili come il TPU.Una cosa da tenere presente è che dopo l'installazione dell'Estrusore Pro, è necessario ricalibrare tutti i parametri del piatto, poiché l'estrusore potrebbe non essere più centrato rispetto al piatto stesso. È importante dedicare del tempo alla calibrazione per ottenere risultati ottimali nelle stampe successive.Un consiglio che posso dare è quello di utilizzare i parametri consigliati da Creality per quanto riguarda la retrazione e i passi dello step sull'estrusore. Questo può aiutare a ottenere una migliore esperienza di stampa e ridurre al minimo i problemi legati all'estrusione.In conclusione, l'Estrusore Pro Dual Gear Feeding di Creality è un ottimo upgrade per la stampante 3D, che offre una presa del filamento affidabile e prestazioni consistenti. Tuttavia, è importante essere consapevoli delle considerazioni e delle calibrazioni necessarie dopo l'installazione per ottenere i migliori risultati di stampa.

sin ninguna duda la mejor decisión que he tomado respecto a la impresora en mi vida, llevaba una racha terrible de atascos, había cambiado el hotend, había probado extrusor de doble engranage, un sin fin de horas y dinero perdido hasta que monté este. Calidad increible y plug and play tanto para PLA como para PETG, quiero probar TPU pero hasta ahora no he malgastado ni un poco de filamento, la impresora no duerme desde que lo monté.No es difícil de montar y además es compatible con bltouch, un acabado muy bonito. MÁS QUE SATISFECHO.( montado en una ender 3 pro con custom firmware en base Marlin).

Buy and off brand version. They are better quality for the same price, for instance copper with nickel coating instead of aluminum.

Parfaitement compatible avec ma Ender 3 pro