Scosche TA02B Stereo Wiring Harness Compatible with Select 1986-20 Toyota, Lexus, Scion and Subaru Vehicles - Aftermarket Radio Wire Harness for Car Stereo . Check Vehicle List Below for Your Model

First off, regardless of what Amazon's results say, this DOES fit my 2006 Tundra double cab WITHOUT the JBL system. Apparently there's a lot of confusion with Toyota stereos, definitely for the first gen Tundras anyway. If you have a stock JBL system, or one with rear entertainment, or even one with rear headphone jacks, you also have an external stock amplifier. If you have an access cab you most likely have one no matter what stock radio it came with. On those radios there will be a single 20-pin plug that leads to the amp (behind stereo in reg cab, under rear seat in access cab, behind back seat of double cab), which has 10 and 6-pin plugs like this harness. You can bypass the amp by connecting this into the stock harness coming from it - but I can't say firsthand how well or if this even really works. Most people use the Metra TYTO-01 instead - Metra TYTO-01 JBL Amplifier Interface Harness . However, some have a non-jbl system with external amp (made by fujitsu ten) and it seems the TYTO-01 doesn't work with that one. At any rate, if you don't know what stock system you have, I'd HIGHLY suggest removing the radio before you order to confirm whether or not you have the jbl, etc 20-pin harness or the 10 and 6-pin harness like this one. I got lucky that my double cab only had the most basic stock radio and this is the correct harness for it. All the wires matched the new stereo's harness and it was a simple plug and play install.

Another good Scosche product. Here's the breakdown: Pros: Works great. I've had it installed for about 6 months now and have had no problems. Fairly easy to put together Cons: Instructions weren't super clear Wire colors didn't match up exactly to colors on head unit, but that's pretty common. Some research in the head unit manual solved that problem Bottom Line: Great wiring harness to hook up your aftermarket head unit to your car. Just be aware that if you haven't done this before, wire colors are typically not all exactly uniform. If it's close, then that's probably the right one, but you may end up with a few stray wires on both ends that leave you scratching your head. Some quick research about your head unit will tell you what each wire does, and then you will have no problem connecting it to the appropriate wire on the wiring harness.

It's a perfect match for my 1989 Toyota MR-2. Flawless connection using DIN wiring standard colors. Simple with decent crimp quality. For those complaining the wires are not labelled, the BAG it comes in has each line identified clearly.

Works in 2009 rav4 sport. At first glance, I thought the car had 6 speakers (two tweeters on top of front door, two speakers on bottom of front doors, and two speakers on bottom of rear doors), but the front two are matrixed. In other words, there are two "tweeters" on the door that is really just audio taken from the front two speakers on the bottom of the doors. (At least that's the way it was explained to me). Hope this helps anyone that may have been confused. If you have a rav4 sport, WITHOUT JBL audio this will work. (If you have jbl you'll have red jbl squares on your speakers if you have jbl and your car will probably be the limited model with leather...in that case, I'm not sure whether this would work or not).

My wire harness came with connectors on both ends not just the factory harness end. Like a dummy though, I thought they sent me the wrong part since it wasn’t the one shown in the photo with bare wires to connect to an aftermarket stereo, then realized the end I cut off had a connector that would connect directly to an aftermarket stereo. All I had to do was disconnect the one on my Alpine and plug this one in. It also has other connectors in parallel to add more amps and speakers if you want to expand your System later. It didn’t come with the pinout but if you are connecting it to a universal stereo with the built in connector you don’t need it. I bought mine from warehouse deals. I suspect someone returned it because it wasn’t bare wires on one end like the photo which may also be why the pinout wasn’t included. Mine was for a 2005 Scion xB. Works perfect. Scion for some reason uses two harness connectors instead of just one. Two speaker channels on one harness and two on the other.

Sometimes you open a radio bay and find out the factory made a midyear modification. It's a good idea to have all the installation aids you can. Being able to wire any which way you want is a lifesaver. Be prepared for the worst and hope for the best. It's nice when doing an install to be able to prep your needed wiring harness "on a workbench" and not while you are hanging upside down under a dashboard! I've spent a few hours laying backwards on a drivers or passenger seat with my feet dangling into the rear compartment. Staring up at the bottom of a dashboard while the brake pedal and accelerator grind into my ears! Too old for that excrement. I buy all the wire kits beforehand and that way I can solder and heat shrink in "comfort" and do a quality job. With room for all the schematics and needed tools to be right at hand! I may end up with spare harness parts, but I can do the install in one fell swoop and not wait for a needed part to be discovered on some dusty back shelf and shipped to me. It's nice to have a place to "bench test" the new head unit before plunking it into the dash. A couple of powered computer speakers can verify your unit is putting out to the RCA jacks a reasonable sound and not "cat howling. You will probably need 4 8 ohm test speakers to verify the high level output. A set of "alligator jumpers is nice to have for temporary test connections. It's a couple of extra bucks for doing a bench test, but it beats having to pull out a buggy new install. (And if it's your wife's car -- )

Very reasonably priced and it made my wiring job very simple. Strongly recommend this item for any stereo install!

We bought this to use with our 2010 Toyota Tacoma and a Pioneer stereo. We have used similar items in the past, and they simply make the entire installation process a breeze. Just a great all around solution, allowing you to do everything at your kitchen table before climbing into your vehicle to do the final install. For the price, these are a no brainer! Would buy again in a heartbeat.

Mejor precio qué la marca que me recomendaron originalmente. Funcionó perfecto para un corolla 2005. El código de colores coincide y los conectores ajustan bien.

Easy enough to install in my Subaru XV (2018). Only issue I had was getting the auto dimming to work.. Not sure if it was a wire thing or just a me thing...

lo recomiendo ampliamente es muy útil y económico,

Arrived on time, no damage, works perfectly. Just need to get wire nuts.