Electrical Wire 20 AWG 20 Gauge Silicone Wire Hook Up Wire Cable 20 Feet [10 ft Black and 10 ft Red] - Soft and Flexible 100 Strands 0.08mm of Tinned Copper Wire High Temperature Resistant

This wire performs better than expected. The 100 multi-strands conduct more electricity at a lower resistance than a single strand wire of the same gauge. The multi-strands also make it significantly more flexible. This flexibility along with the extreme flexibility of the silicone insulation make it easy to make tight bends and snake the wire into very tight places. The 20' of wire is enough for multiple projects.

Redoing motor wiring? This is the wire to get.. very high quality wire that handles current up to 8s very well for motor wiring.. when I change motors I take the motors I just swapped and go ahead and cut the heat shrink off them and put a fresh run if 120mm of wire back on them so they are ready for another build should I reuse them or they are ready to be sold if I plan to sell them... I hate just joining wires it looks sloppy and adds a point of resistance that isn't needed.. take fresh wire and do it the right way... on closed bottom motors it's harder to do, on the new open bottom stuff and almost everything made now is open bottom it's super easy to do so long as the wires and heat shrink aren't epoxied to the windings on the bottom.. then it can be a bit hard or impossible without causing damage.. in that case you cut the wires fairly close but leave about .75 inches of stripped wire and make a nice clean spliced joint don't just lay the wires over each other and solder together that's a no no.. properly splice them then you will have resistance that is close to if it was a solid place of multistrand wire. I do my wires with red for the middle wire and the two outside wires black.. the reason I do this is in case I'm at a race and don't have time to swap the motor then jump in BLhlei and change motor direction, I just check the way the motor is solder and the red wire helps with that then solder the new motor on and on ready to go. Plus changing the motor direction requires a tad bit more processing in the esc that just isn't needed solder the motors on the correct way and make life a little easier on the esc processor you will have less desyncs on high KV motors if you do this to. It's just better all the way around.

These are good wires with the correct diameter and conductivity. The sheathing is soft silicone and the strands are fine. So it is a great product for wires that are subject to frequent bending and mechanical stress.

Worked perfect for new door bell. Wires are coated in a smooth durable flexible coating. I would purchase again. But, I only needed about 4” of wire, so I think I have enough to last me for a long time.

I have been looking for this kind of wire for years. This is a 2-conductor 'zip-cord' version of the silicone wire frequently used on RC vehicles, quadrotors, and Li-Po batteries. It's extremely flexible and soft compared to the usual PVC-jacketed 'speaker wire' type stuff. It also holds up to extreme heat because the silicone insulation will not melt like plastic does. It also remains flexible at very low temperatures when PVC insulation becomes rock-hard. I would choose this type of wire over the standard PVC stuff for almost any project. It's so much easier live with. The only downside to silicone wire is that it can be knicked/sliced quite easily, so it's not as good in applications where it's in direct contact with sharp edges or when pinched between metal parts.

I bought this wire to install a ceiling lamp, LED light bulbs and less than 20 watts, according to the specification this one works.

This wire worked great for my drones and planes. Didn’t have any issues with it. Felt like a quality wire didn’t feel cheap. Was really easy to solder and work with

Good cables. Important for me was the ability to be able to cut, bend, crimp or solder them in any way I want. I can do this with these ones.

Muy buena calidad y precio para cableados de baterías lipo u otros usos

Works As described. Soft and flexible.

Very good wire again thankyou seller. Its very soft and flexible, outter coating a little thin but definitely 20 gauge, all good 👍

Works well for junction cables

As described. Fairly Flexible.