JIUSHARK JF13K Diamond,Top-Down CPU Air Cooler,6mm x 7 Copper Heat Pipes 2×120 * 120 * 15mm PWM&ARGB Fans 250W TDP SuitableFor Intel LGA 1700/1200/115X AMD AM5/AM4

This thing is great, the mounting directions suck, but the performance and cost more than justify this cooler. I used this in a server rack case and had to cut the case above the motherboard IO faceplate. A bit of rubber around the cut and it's right as rain. Does it look weird? Yes. Does it provide massive cooling? Also yes. This thing is great for my game server, and the low maintenance, low profile, and high performance can't be beat. I have been using this for about 6 months and it is my favorite solution for a 4U server rack mounted pc.

Great product

Works very well, a little difficult to install compared to other air coolers as I had to remove my rear exhaust fan to do so. Just moved the rear to a top exhaust position.

I have been using this cooler for over a year, and I have no problems with it. I have in a micro ATX Thermaltake Tower 300. While it does take up a lot of space, I really like the look of it, It makes my PC stand out from all of the AIO and regular air-cooled PCs. It keeps my 5800x at 38C while idle and in the longest of gaming sessions it never goes above 75C. I have also swapped the fans out to give a better look from the cheap fans that are included. Overall, I would recommend this cooler.

Performs very well, the fans are pretty silent even on an open air chassis

Works well with my i5 14600k. No overheating problems either which surprised me with the design

To put simply. My computer is now dead. Yes I followed the instructions, yes I removed the film from the contact plate. Yes, I'm now depressed because my 1200 dollar pc is dead and now I have NOTHING to look forward to after my 10 hour shifts at work. And no, I can't afford to just replace my pc.

The black looks really nice with ARGB halo fans you will need longer ME screws to mount standard 120mm fans. The mounting system on this absolutely sucks. The combo backplate is cheap, it works but would be nicer to have dedicated AMD and INTEL plates. The screws fit loose into the MB holes and have a small collar that pinches and could damage. the board. The screws are also too long if you have 6mm standoffs you will have to drill some holes in your case because the screws hit and will warp the board. The nuts should be replaced with low profile shoulder screws that fit the mb holes and some plastic spacers to set clamp pressure similar to how Noctura does it eliminating the board pinching. CPU interface had some sharp burs on the edges that I could feel with my fingernail. I used an 800 grit emery sponge around the edge to remove the burs. Temps are great on an i9-12900K. I would definitely buy more if they fixed the issues.

Es la segunda vez que pido este disipador porque no trae la placa trasera del AM5 socket, si vas a pensar instalarlo en un AM5 mejor evitalo o consiguete la placa trasera, tendre que devolvelo nuevamente

Nachdem ich im Netz einige gute Reviews gesehen hatte, beschloss ich mir den Kühler zu kaufen. Lieferung aus den Staaten ging recht schnell. Beim Auspacken wurde die Enttäuschung immer größer. Der ganze Kühlkörper wirkt in sich verzogen, wahrscheinlich weil die Lüfter auf Biegen und Brechen draufgeschraubt worden sind und die Bohrungen anscheinend nicht zu 100% passen. Die Kühlfinnen sind sehr dünn und wirken billig. Die Abstände zwischen den Kühlfinnen sind viel zu gering wodurch kaum Luft durch den Kühler zieht. Vielmehr wird du Luft nur draufgeblasen. Der Kühler ist nicht ordentlich gelötet oder ähnliches. Nach der Montage klappert der ganze Kühlkörper auf seinem eigenem Sockel, da die Teile eher eingehangen sind als alles andere. Nicht zu empfehlen. Es gibt günstigere Hersteller mit weitaus besserer Qualität.