YOOPAI 3D Printer Enclosure, Dustproof Tent Constant Temperature Protective Cover for Creality Ender 3 V3 SE/KE/Ender 3/Ender 3 Pro/Ender 3V2/Ender 3S1/Anycubic Elegoo, 29.5×25.6×21.6"

My home has no climate control other than wall heat, so when our lengthy rainy season hits, the indoor humidity goes up. 45-51% indoors on average. Even small PLA prints stopped sticking to a PEI build plate. Running the machine inside this enclosure (Ender 3 with a top mounted Sunlu S1 dryer- 29.25" tall, but they fit) dropped the humidity around the machine by 20-25%, and 4 small dessicant pots sitting inside dropped it even more. The air envelope around the machine is now 98°f, and 14% relative humidity. Couldn't have hoped for better results. Be aware, these are very large, and will require a surface about 30" deep to sit on as the internal frame isn't really strong enough to allow the front end to hang off in space unsupported. Take care in assembling the frame. Make sure the mid span connections are fully seated, as are the corners. Make sure you are pushing exactly straight, compare the length of assembled spars, and candle the corners with a flashlight to check that they are fully seated. Uneven pressure could break the couplings, and even drive the fiberglass rod into you if it were to break. The fabric cover is a very snug fit, but it needs to be. Work it over from rear bottom edge to rear top edge, then bottom front, and finally roll the top corners on. It'll seem almost too tight until you finally roll those top corners on. Also, since you'll have it fully unzipped, try not to trap your zip tabs behind the rear part of the frame. These work really well to stabilize the envelope around your machine, at a good price.

It was very easy to assemble, be careful with the connections between pipes, they can be fragile if you apply a lot of force to them, so far it has helped a lot to reduce smoke, using an Anycubic m5s pro, it is a large printer and there is still plenty of room, and the fabric material is very resistant.

Great product

I had originally rated this as a one star while I was assembling it but have changed it to a three star after actually using the product. The instructions are beyond terrible and the support rods require gloves or else you'll get fiberglass splinters during assembly.The good:-Cheap,-Does what it advertises.-Using an exhaust tube that leads outside lets me have this in the room with me as it prints with no ill effects that I can detect even after hour long prints.The bad:-Horrible instructions. If you do not firmly insert the rods into the connectors with lots of force, it is literally impossible to assemble this. This is not mentioned anywhere in the instructions and I had to read other Amazon reviews to find it.-Questionable tolerances. You have to bend the fiberglass poles a bit to get it to fit the cover. While mine wasn't too bad, I had no idea that you had to do this. Another strike against the horrible instructions.-Shoddy support rods. Wear gloves when you assemble this. I did not and I got two fiberglass splinters in both of my fingers that worked themselves out over the next 24 hours but was quite painful while I had them.

Does not fit Ender 5. Almost does but the spool holder protrudes and you have to fit the Ender 5 in so that the side of the ender is facing the front of the enclosure. The enclosure seems well made just doesn't fit Ender 5 as stated.

The cover does not fit over the frame, even with all the fiberglass rods snugly seated. Any attempts to stretch the cover over the fiberglass frame resulted in the cover ripping at the seams and the fiberglass rod literally shattering, rendering the product dangerous and unusable.I recommend you do not buy this product unless you're crafty enough to build your own frame. The cover itself seems nice minus how easily the seams came apart. I'm not sure why the reviews on this are so high considering EVERYONE seems to have similar issues with the installation...

Perfect fit for my 3D printer (Entina V2 dual extruder). It took about an hour to set up. I use a dry filament box the same as so I made my own holes at the to to feed the filament through.

Makes a huge difference in printing with ABS, ASA, Nylon, and other hard to print filaments. Good value for its size being easy to put together. Well designed for wiring and ventilation port in the back with reflective heating panels to keep consistent temperatures within . Dual zippers allow you to open fully or partially to retain heat.