NUMAKERS PLA+ 3D Printer Filament, 1.75mm, Dimensional Accuracy +/- 0.03 mm, 1 kg Spool (2.2 lbs), Compatible with Most FDM Printers (Magenta)

at first I was skeptical about the print quality of the filament, the filaments i bought from other brand or seller were all brittle (filament breaks at the middle of printing) but this one prints very fine and addhesion is good👌 will buy more again.....

Quality very nice. Apperance as shown in pics. Packing was also good.

The product is great. Came packaged well. Prints are so much nicer than the PLA I received with my printer.Only complaint is the spool is not wrapped neatly. Other than that it's great.

Good quality filament at reasonable price

You're on the right path, keep going!

The media could not be loaded. So i basically printed a benchy with this filament at 500mm/s and surprisingly the print came out almost flawless. Adhesion is good, I'm printing at 220°C extruder temp and 55° C bed temp, most other prints at 300mm/s are also very good.

Prints well at 205C/60C on my Ender 3 v2, but had to do a lot of messing about to get bed adhesion right. I used a lot of glue on the bed to get good prints initially, but eventually switched to a PEI bed. Once you get the first layer right though, the strength and quality of the prints is good.

I purchased 2 colours filament one Black and one Green and I started my some projects with Black filament than I thought I must try with other colour too so I tried with green and my 4-7 days goes waste and I am very disappointed with this filamentI tried bad alignment temperature tower and try with 180 C° to 240C° but no resultSo I lost my money that invested in Green filament..!I am crying 😭 whenever I see the Green filament..!Now I am afraid to buy other then Black and White colour..!I can't believe that colour is also matter in filament with same product with same brand...!😭

This prints very nice, I won't lie, however this is the first filament to ever get jammed inside my nozzle and absolutely refuse to come back out. Not once, but twice. The only fix was to snap it off at the bowden tube and shove new filament in and push the rest of this stuff out. Color is not teal more like mint green.

First time using this filament and it's been great so far, looks good, spool was wound real well. Filament was tough after printed. Already ordered 10 from their website as they have a discount for ordering 10 rolls or more.

Tried this brand for the first time and now I'm hooked. Prints great, color is the best red I have ever used, very rich and vibrant. I have found it likes to be on the hotter side for the nozzle, about 225. Bed I leave at 60 and no issues at all. Have used it on all 4 of my printers, Elegoo Neptune 3, Mingda Magician X and 2 Kingroon KP3S Pro S1 by Sliceworx.com and prints amazing on all 4.

Recently purchased a printer. A generic white PLA came with it and naturally, I began by printing a small trinket. The geometries were too small for the PLA and the print quality was unusable. The part included a .5in unsupported overhang at a very shallow angle which more or less collapsed with the normal PLA. After buying this roll, I attempted the print again with entirely different results. Printing at a standard 200C and max quality of .12mm the part came out perfectly with almost no discernable collapse in the overhang and sharp edges to every surface. The filament makes all the difference and for the price, you cannot go wrong with this. I haven't compared it with others at this price point yet, but the quality is consistent enough, such that no print has failed, that I'd order it again.

I really don't have any major complaints with this filament. It's a great color and it prints beautifully. It adheres well, even to other colors. I did some rainbow prints with other Numaker filaments and had no issues getting them to stick to each other. I was able to get all the other colors for the Numaker website, but they didn't have green in stock, so I ended up buying through Amazon. I would recommend buying directly from their website if you can because it's much cheaper. The spool is a little hefty for my taste, I prefer minimal plastic or a cardboard spool. That said, it's better than most and they give plenty of holes along the edge to secure the filament between prints and the side is windowed, so you can easily visualized how much filament you have left.