Creality Ender 3 V3 SE Hotend, Ender 3 V3 KE Ceramic Heating Block Kit with Quick-swap Nozzle, Upgrade Hotend Kit 300℃ High Temperature 600mm/s High-Speed Printing for Ender 3 V3 SE/KE 3D Printers

I must've had a bad stock hotend because after I upgraded to this my prints looked immensely better. Added to that I don't have to wait as long for the hot end to heat up as compared to the stock one on an ender 3 v3 se. I wish the tips were priced a little more accessible as well as their sizes. I had to really look to find a smaller tip than stock, I didn't buy it but it's nice to have the option for those ultra high quality prints. The PID calibration did not go as planned and it errored out, does not cause any problems with actually printing and I still have to research the cause.

Great replacement over stock hot end. Easy install. Works great

At some point, you are going to not pay attention to your printer for a little while, and at that exact moment, it's going to notice you aren't there, and will immediately start to clog. 'If' you catch it in time, you can just give it a wipe, put on a new sock, and go about your day. But if you don't... you'll be pleased to have one of these spare in a drawer, as you wait for the printer to cool, and then slowly detach the blob of PLA that is now solidifed around your ENTIRE hotend and heating block!

This is the third hotend I bought. I do a lot of printing. I do think these hotends burnout faster then the standard hotend, the print results are much nicer with thus hotend. It comes down to what your looking for. It you aren't looking for better quality prints, stay with yhe cheap standard hotend. This hotend upgrade delivers I feel better quality prints. Its easy to install (much easier than the standard). The quick change nozzle is no quicker then the regular nozzles, but the the nozzles are better quality and what I feel makes a different on outcomes of prints. I do recommend this hotend if your looking for better quality prints, but keep an extra hotend ready. My hotends have lasted for around 8 to 9 months, but I also do alot of printing.

This is a fantastic buy! I purchased this to replace my old hotend. A bonus to this is it comes with a hardened steel nozzle as well so you don't have to worry about longevity. The install process was straight forward and worked right away on the first print.

Few months of owning everything was going great then started getting bad layers and upon watching through my camera on my nebula pad i noticed my nozzle shift so i disassembled the hotend to find the heat break where the hotend ataches is stripped.

Hot end works great but do have a hard time getting the filament past the copper neck. The neck needs to be flanged or thinner at the top as the filament hits the neck and stops. It takes me forever to get the filament fed into the system.

Upgraded Hotend with ceramic heating block well worth it - much more precise and faster! Well worth it to upgrade over the stock one on the V3 SE - This hotend combined with the Nebula kit made such a significant difference on my V3 SE

No lo recomiendo me quemo la placa lo instale con la impresora apaga verifique las conexiones antes de entenderla y después ya no hace el home correctamente ya cheque todo , finale de carrera, conexiones , cargue firmware de nuevo cambie al viejo hotend y mismo resultado.

Install was easy and straightforward, Previous issues with fan screw length have been well resolved Could not be happier.

el calor pasa a la garganta de admisión del filamento, se ablanda y se obstruye solita. Mi solución provisional ha sido imprimir todos los filamentos a 190°C y bajar la temperatura de la cama a 30°C. De otra manera se ablanda, se engrosa y se tapa solita. Actualización al 8 julio 2025; aun bajando la temperatura se sigue obstruyendo. El tubo de reflon se ha calentado y deformado a 190°. Le voy a meter un ventilador adicional porque las aletas del disipador siguen calentadose demasiado.

Excellent hotend; it allows for higher printing speed, better material support for non-PLA stock, and less chance of installation error. Definitely worth the money. I think "Quick-swap" is a misnomer though. You still seem to need to disassemble the toolhead and remove the extruder to switch nozzles. The only time this saves saves you is that you don't need to hot-tighten afterwards. So just manage expectations; you're not popping these in and out much faster than the normal nozzles.

Good and works well as advertised. Instructions for Creality V3 KE should have been a bit more descriptive but wasnt too big of a deal.