Freenove 4WD Smart Car Kit for Raspberry Pi 5 4 B 3 B+ Zero 2W, Face Tracking, Line Tracking, Light Tracking, Obstacle Avoidance, App Control, Camera, Servo (Raspberry Pi Not Included)

マニュアル（PDF）や組み立て動画があるので、初心者でも簡単に作れると思います。 組み立てた後、動作せず、私の手順が違うのかとサポートの方とメールでやり取りしました。 まず驚いたのが、１日以内で返信をくれるという返信の速さ。 メールの内容も丁寧で分かりやすかったです。 何度かやり取りした結果、新しい基盤を送ってくださり、無事に動くようになりました。 トラブルが起きたとしてもメーカーのサポートが充実しているので、安心して購入できる品だと思います！

supportメールは、英語ですが対応は親切です。 基盤に不具合があり、電源が最初は入ったのですが、そのうち入らなくなりました。 メールでのサポートは、きちんとしてくれます。 最終的には、新しい基盤を送ってくれました。

マニュアルや組み立て動画は分かりやすく作られいます。メールの問い合わせも丁寧に対応してくれました。

プログラミングできる Raspberry Pi ベースのロボットキットが欲しくて購入しました。 本商品の他に、Raspberry Pi CPUボード(私は 3B)とリチウムイオン電池 18650 x 2本を購入する必要がありますが、それを入れてもペイする機能の商品だと思います。 英語ですが、詳しい解説書が用意されており、また、テクニカルサポートも丁寧な対応ですので、困ることはありません。 サンプルプログラムだけでも楽しめますが、自分でもプログラミングできるようになりたいです。 動画は超音波センサーで障害物を避けて自動走行しているところです。

作るの簡単動かないけど

多くのセンサーを積んでおり、最初からライントレースなど多くのプログラムが用意されており、 組み立てたら完成のような製品です。 Freenoveの中でも現状で最も力を入れている製品で、マニュアル動画が充実しています。(英語ですが・・) pdfのチュートリアルもありますが、こちらは少し誤りがあります。 不満な点は、頭を激しく動かすとカメラのフラットケーブルが外れやすいところかな~

製作する者のスキルが現状では必要です。しかし価格を考えると最高の製品です。 後方左車輪を止めるためのナットが基板にあたり、削れ、5VとGNDが短絡しました。注意が必要です。 ナットの位置のDCモーターの+5V側の線になります。次回、引き回しで回避願います。私は絶縁シートを入れました。ほかの方の書き込みにもありましたが、駆動DCモーターの極性がプログラムと逆でピンを赤黒入れ替えました。

設定方法に１、マニュアル（PDF）と２，動画（you tube)があるのですが、両方を重ねながら組み立てとラズベリーパイの設定を進めるのですが途中から両者が違ってくるのです。サポートに問い合わせをするとマニュアルを優先してくださいという返答でした。でも、マニュアルも他の機種のプログラムをインストールするように指示があったりするので、サポートに問うとマニュアルが間違っている気にするなという返答です。何とか悪戦苦闘して設定と組み立てが終了。でも、まったく動きません。サポートに問い合わせると電池ホルダーに不具合が多く電池を指で押さえれば動くという返事でした。しかし、いくら指で押さえてもびくともしません。この商品は初心者では無理です。商品自体もはずれです。

First, the product works if you assemble it correctly (see my video). My kid and I really enjoyed the features such as auto-driving, obstacle avoidance and etc. The kit really deserves five-star for its functionalities. However, there are a few issues. One issue is that the car kit doesn't come with rechargeable 18650 batteries. I ended up spending some time on Amazon doing research and buying a bundle of these expensive batteries and charger. I wish the car kit can include batteries and charge a little extra. My second major issue is that the manual is poorly written. There are duplicated sections all over and it can confuse people. Most importantly, some key installation steps should be emphasized. For example, my kid was stuck between Step 9-11 on Page 51 (duplicated on Page 72) when attaching camera module to servo package. After quite a while of watching the video of assembled car like a detective to gather clues, I realized that one needed to attach a white rocker arm on Step 9. Then Page 73 says there are two ways to fix the servo 0. I don't think the second way works. Another example is when wiring the ribbon for camera (Page 54). A kid would simply insert a ribbon into the slot. Step 1 on Page 54 should emphasize that one needs to pull the lever out first, insert the ribbon and then push the lever in. In retrospect, the car worked great. I am surprised that the installation of software is very smooth. The assembling process was frustrating sometimes and there is a lot of room for improvement and simplification.

The well designed parts and 128 page instruction manual including the computer code make this car easy to assemble and operate. The ability to handle the testing of each module on a PC via RealVNC facilitates testing, and the phone app provides steering and speed control as well as control of the LED lights, camera and switching to other modes of operation. Tech support provides 24 hour responses via email and was very helpful for straightforward problems. All in all this kit offers a lot for the money and earns a five star rating. However, I encountered a couple problems that should have been handled better and distracted from my overall enjoyment of the project. Next to control from a phone the most useful function is the obstacle avoidance using the ultrasonic sensor for control. The ultrasonic sensor that came with the car kit was defective and was replaced after three weeks for overseas shipping. However, the replacement sensor was also defective, and in spite of my detailed documentation of the problem Freenove refused to replace it. I had an ultrasonic sensor from another project which I was able to use but it had intermittent errors that severely compromised this important function. The other problem was less serious but annoying and time consuming. The code downloaded to control the car had an error which applied less than a third the required power to the wheels for forward motion. Therefore, the car refused to move resulting in several days of emails blaming the problem on the batteries before I finally traced it to the code error. It has been three weeks since this problem was reported to Freenove and a download of the code today showed the error had not been corrected.

It says so in the description, but do note, you need a Raspberry Pi (I used a Pi 3) and two 18650 batteries, which are not included. I was very keen to build this and try it out, so I downloaded the code and set up my Raspberry Pi, shortly after placing my order. Fortunately, I already had a couple of 18650 batteries. So, when the kit arrived the next day, I was good to go. Assembly took about 2 hours. First point to note is that I have big fingers and some of the screws are really tiny – I needed fine tweezers for these. Second point, when assembling the pan and tilt ‘head’, the instructions tell you to plug in the servos and run servo.py to put them in the correct position before assembly. I would recommend carrying out steps 1 to 9 of the 11 illustrated steps (page 51 at time of writing) before connecting the servos. I would also suggest connecting the cables to the camera and ultrasonic units before connecting the ‘face’ to the ‘neck’ as they are lot more accessible at this point. Excepting a couple of fiddly bits, the kit was straight forward to assemble, I ran all the test modules and everything worked first time, except it went backwards instead of forwards – but the instructions covered correcting this. It does everything shown in the Freenove video and can also be controlled directly by a phone app (android in my case). I was impressed by the quality of the build and also that all the code is open source. At the price, having a kit you can control from your phone, pretty much out of the box, is already good value, but the potential for writing your own code is even more appealing and I would imagine would be a great incentive for novice coders. I hope a community will develop where people can share their code and ideas. I also think the kit is ideal for further development – a robot arm would be a cool addition, perhaps Freenove may develop expansion kits in the future. In summary, a great kit, a great learning tool and best of all – open source!

Liked the kit, but the instructions has some holes and the mobile apps required to control the model leavs a bit to wish for. But over all it has potential and I will most definitely have fun with this one. All the parts are there, well packed and easy to follow instructions, but a bit un clear at some parts. Will get more kits. And I'm planning to upgrade this one.

Rien à dire, juste incroyable Le montage, super simple Le paramétrage pour le raspberry (obligatoire) un peu moins simple mais en suivant les différents tuto, c'est relativement facile à comprendre enfin jusqu'à maintenant