Comgrow TPU Filament 1.75, Flexible 3D Printer Filament, 95A Soft fit Most 3D Printers Dimensional Accuracy +/- 0.02mm TPU Yellow 1kg (2.2lbs)

Printed flawlessly right out of the gate on my Bambu Lab P1S. I used the "Bambu TPU 95A" preset and didn't even have to make any tweaks. Easy to load, although I would not recommend trying it in the AMS. It *might* work, but it's generally accepted that you'll want a firmer TPU of at least 64D to get reliable results there. I just fed mine externally from a dry box I made from a 4L cereal container. I didn't need to dry it first. End result looks crisp and clean.

This was my first foray into printing TPU. This stuff printed off like a dream! No notes. I made a table that sits in between couch cushions that has a TPU top which is what is pictured. File on maker world

TPU works great more some seals out of it no problem

Seriously impressed with this filament! It prints so smoothly with hardly any stringing, which is a huge plus for me. The bed adhesion is absolutely fantastic, no lifting or warping whatsoever. I haven't had a single print fail due to adhesion issues. I'd definitely recommend giving this stuff a try for your next project.

Great filament that works very well! I will definitely purchase again.

Es muy bueno, ya habíamos probado con otros ABS, pero tenían muchos problemas de adherencia, este se pega fácil.

Cumple lo que promete

Compared to my last filament (eSun PLA+) I found this filament is super difficult to use on an Ender 3 v2. I have it mostly working now, but it was a lot of work getting it to even stick to the bed. Retramming the bed very carefully helped a lot, as did reducing the speed of first layer to a snails pace (<25 mm/s). On my 0.4mm nozzle, this filament tends to curl up tightly around the extruder just before print, creating a wadded nest of sticky filament that scrubs the bed clean of anything you were hoping to lay down! Using a generous skirt and manually snatching wads with tweezers during first part of print solves this, but it’s annoying. I also found increasing the flow rate for the first layer helped. The diameter I measured on my roll fluctuates a fair bit, and also averages a lot thinner than the rated diameter: 1.71mm is a typical diameter, but it can be as low as 1.69 or as high as 1.78. This is well outside the 1.75 ±0.02 in the description and makes it difficult to dial in flow rate. This PLA is much less rigid than PLA+. This is expected if it’s a truly pure PLA, but something to be aware of. I can’t be totally sure, but I seem to be having more problems with stringing, too. This is also to be expected with pure PLA, but worth being aware of. Other reviews have pointed out that the white color is quite weak. I agree but, as long as you’re expecting it, I don’t think that has to be a bad thing. Functionally, it’s opaque, but you will get subsurface scattering with this white filament, as it’s very (very) slightly translucent. I like the look of it. I’m pretty new to 3D printing, but I’ve tried a few filaments now, and the above problems with this filament are new to me. I wouldn’t recommend this to a beginner. Perhaps different nozzles, or 3D pens (?) would have more luck. Other than these issues, it actually is totally fine once you get printing. But I’d counsel shoppers to consider whether saving a few dollars on a roll is worth the many hours of your time troubleshooting and printing test towers dialing in this filament. 🤷

Love this product, I always keep a spool of it as my go to filament for reliability and quality product, never have any problems , adhesion to build plate is excellent ( creality mag bed) i dont use any products to aid adhesion , the quality of the print is great with a nice shiney appearance and colour is uniform, cost is good although a touch more expensive than some filaments I have used ( usually Basicfil) iyts worth it as you know your going to get a good finished product. Thoroughly recommended.

Spule kommt sauber aufgerollt, vakuumiert und mit Silica Gel Beutelchen. Material lässt sich super verarbeiten und ist nicht sehr brüchig. 205 Grad Düsen- und 55 Grad Betttemperatur sorgen bei mir für perfekte Haftung und Verarbeitung. Werde auf jeden Fall noch andere Farben nachbestellen. Weiter so Comgrow.

El bobinado no da ningún problema. Se imprime perfectamente, he comprado varios y el negro es el que encuentro que se pega mejor a la base. Ni atascos ni problemas de configuracion para el material imprimo a 195° y 60° para la base.

Lo compré teniendo en mente el que traía la Ender 3, de la misma marca ambos. La verdad es que me ha sorprendido la calidad del mismo, no se notan las líneas de las capas y funde a una temperatura muy reducida. Yo lo quemo a 195ºC y los resultados son muy sorprendentes. Muy recomendado.

My favourite filament. Such consistent stuff for such a reasonable price. All I really have to say, just prints so well.