DSPIAE ST-A Ultra-Thin Single Blade Nipper 3.0

So far so good. Works great. Feels great. Haven’t broken it yet

For the price, these nippers are incredible. I couldn't justify the cost of the godhands over this pair of nippers after reading reviews and watching other modelers use them in their work. I really like the single bladed nippers the best and these things cut very cleanly compared to the cheap nippers I originally used. If you're into building model kits, you need a good pair of nippers and these are worth the money.

Haven't used god hands yet. These have held up great and work reasonably well. I have no other single sided nippers to compare with unfortunately. I can't see how other brands would be significantly more. Unsure what current prices are in the industry but at the time when I purchased these there was a sizable price difference (these were about $38? Vs god hand 120's @ $64. I'm actually impressed with the case and the leather sheath. Both work well and I enjoy storing and taking them out of the case when needed.

Is it sharp? Yes Does it cut flush? No. There's a noticable amount material which I have to sand down or use a different pair of nippers to clean up. I just went back to using my old, cheaper nippers instead, even though they are worn out and a bit duller because they trim flush and make the whole process twice as quick.

Very nice. But, care must be used with all high quality ultra-thin single blade nippers as you can break the blades off very easily.

These nippers are a definite step up from my old double-bladed nippers, but they're no game-changers. The cuts are easy and clean, but they're not particularly flush. I don't know if there's some secret to getting better cuts, but even on a flat part I still always need to clean up with a hobby knife. Still, they feel good in the hand and the covers and box are nice to keep them in top condition. I'd buy them again, just temper your expectations.

Excelente articulo

Great step up for gunpla building. The nippers are sharp and firm. The cut is clean with few to no stress marks, even when cutting softer plastic.

Sehr gute Zange für feinarbeit von z.b. Warhammer

I've only had these nippers a short while, but they really impress. The cutting is easy, clean, & precise. I'll leave it to the other reviewers to extol their virtues in detail. This review is more about sharing some practical info. These nippers do leave a tiny amount of material behind for manual cleanup, but it truly is minimal, and it's also by design. When you closely inspect these nippers, you will see that the back side of the sharp cutting bade does not align exactly with the back of the blunt side. This is not a manufacturing error, and the reason is covered in detail in the included manual. In short, it's to ensure that the cutting blade (which is very thin) is not laterally displaced too far during cutting, and fails to accurately meet up with the blunt side - potentially leading to wear or breakage. As mentioned in the headline, some additional user setup may be required for optimal use. Unfortunately, this is not covered in the manual. Throughout reading reviews and learning about usage mistakes which have led to breakage for some users, and watching Youtube videos explaining proper use, I would like to pass on some information that will hopefully be of some help in getting the most life from these nippers. Credit goes to Youtube user "Florymodels" who made a very informative review/tutorial for these specific nippers. In short, there is a "limit regulator" screw that *must* be set up correctly, and which - in my case - was not correctly set up on arrival. Its purpose is to prevent the user from being able to squeeze the handles with more force than is strictly needed to make the intended cut. What you want to do is grab yourself a normal piece of A4 printer paper, and use that as your cutting test subject. Loosen the nut on the limit regulator, and then use the tool included with the nipper to set the position of the regulator precisely at the point where it stops against the opposing grip handle when the piece of printer paper is cut; no more, and no less. If the nippers won't close enough to cut the paper, retract the limit regulator until it can. If the nippers will cut the paper, but the limit regulator is not touching the opposing grip handle, extend the regulatory until it rests directly against the opposing grip handle. When you are finished, tighten the regulator nut, and test again to make sure everything is set up correctly. The limit regulator screw is prone to wear somewhat with time and usage, so be sure to perform this adjustment again every so often... if you don't, it may lead to a shortened life for the nippers. Hope this is of some help!

Is it worth the money spent. You have to decide. If you are a plastic modeller and have followed the reviews for this type of cutters. It lives up to it's very positive reviews. It is my go-to nippers for small parts on the sprue. Not meant for heavy cutting. I like them . Did not like the price.

La pince coupe parfaitement. Elle ne fait pas comme les autres où elle presse où ellesse les traces de tension. Elle coupe net pour ceux qui font de modélisme. Je vous recommande grandement surtout pour ceux qui sont dans Warhammer. Ça aide grandement niveau travail et finition mais aussi on gagne du temps

J'avais une pince de précision classique ,et après avoir vue des vidéo sur la Dspiae je me suis décidé à la comander, et bien c'est parfai ,la ou la pince classique laissait de trace de pincement ,celle là c'est un autre monde , pas de trace de coupe ,le temp économisé sur le montage est faramineux sur les MG 👌🏻 je recommande !