Mowei [3+2 Pack for Galaxy S23 Ultra Screen Protector [Fully Support Fingerprint & S Pen] 3X 3D Curved Tempered Glass & 2X Camera Lens Protector for Samsung S23 Ultra 5G

So.. after many many many searches for a suitable tempered glass screen protector for my S22U I finally found one that actually works with the fingerprint reader!Previously purchased the Dome Glass protector and whilst the application process is very similar to this one, I had much more issues with the Dome one, inc bubbles that wouldn't go, glue not curing properly leaving patches at edge looking annoying, 50% chance of a working fingerprint reader, and being slightly harder to install properly.My worry was the application result, for this one would also be similar and leave me unimpressed... And it very nearly was!I watched the instructions video (which btw was for s21 ultra and not this phone), plus another video of a youtube reviewer applying this.Main thing I learnt throughout the process was be patient and do it slowly!I followed the instructions, also used the UV light to check for any specks left on the screen prior to glue application (which was a good call!). After finally getting the screen clean enough to apply the glue, I slowly dropped the protector on top as instructed, but ended up with two different bubbles (one on left of screen, one on right).Instead of panicking I used the included tool (safety knife) to slowly lift the screen from the edges closest to the bubbles until I got to them, and then slowly let it fall back down whilst applying gentle pressure from the top to push the bubble towards the edges. Took me a good 5-7 mins of doing this repeatedly til I got a clean application, and luckily there was enough liquid glue under the screen left for me to actually do it!Applied the included weight onto the fingerprint reader area (leaving the sticky plastic on) and did the first curing with UV for 50 secs.Then removed the phone from the holding case, wiped down the edges and did another 2 mins UV application from center.Finally after ensuring the edges were free of glue I did 30 secs curing on both left and right hand side for the last bit.And that's it, it was done! Clean application, took a while and it was fiddly af but job done!The protector is not full height of screen, so if you do need to move to get bubbles out, just bear that in mind as it will move up and down as you touch it. Mine has a slightly bigger gap at top of screen and bottom is flush with the edge but it looks fine for now.Just something to know for next time!Protection wise, will have to wait and see how it performs but in terms of screen feeling after application it's perfectly fine. No issues using the screen and it feels like glass should, without any random touches etc. Also didn't need to increase sensitivity within settings, works fine.I had no fingerprints registered prior to application btw, only applied them after application. Also you might need to put bit more pressure for it to register but so far so good!Recommended product, just make sure you have steady hands, don't rush the application and *only* cure once you got the initial application right, no bubbles and a clean screen!

I've been using resin screen protectors for years and this the first time I've seen this problem. At first the application looks perfect but within the next few days the screen protector delaminates in this strange ugly pattern that's impossible to ignore. I have tried 2/3 of the screen protectors in the pack and they both do the same thing and yes I watched the video carefully. As other reviews have said, you start off with no air bubbles then one forms in the middle and slowly gets bigger until the screen protector is ruined within a few days.This type of protector normally lasts me 6 months to a year so it's been a massive waste of money for me. The only time I've seen a similar issue was with a tempered glass screen protector sold for s22 ultras but actually made for s23 ultra. The dimensions are similar but one has a more shallow curve. I suspect that's the issue here otherwise normally with resin, if there are bubbles they stay where they are. They don't slowly get bigger until the screen protector falls off because the resin hardens during the application process so air shouldn't get in unless there's something wrong with the screen protector itself.The screen protector eventually cracked where the air bubble formed and left tiny scratches on my screen.

Update: after seven months on my phone this protector just saved my screen from a major drop. The phone fell about five feet face down onto stony tarmac, followed by my foot! The screen protector was trashed. The phone screen has not got a mark on it. Best hardened glass protector I've had.The bad bit first: this is not a simple screen protector to fit. I'm used to films, dry and wet lay, tempered glass, "air" glass etc. I've never had to use a UV cured glue before. It takes time, patience and care to get it right. Watch the instruction video and, preferably, someone else's video too. The glue can be really slow to fully spread under the protector, BE PATIENT! And, because it's UV cured and it can take a while, I'd close the curtains just in case. Once you switch on the UV the initial cure is really fast, and then you're stuck. It's a bit of a faff, and I screwed up the first protector being impatient.Now the good bits:Of all of the curved screen protectors I've used this is the closest fit of any glass I've used. In my case there's hardly any gap at all.The oleophobic coating, and the feel of the screen, is very close to the bare glass. It's really good.Generally I find tempered glass protectors, especially on curved screens, really easy to crack. I've had no such issue with this protector, it seems very robust (touch wood).The fingerprint detection is excellent. (Note: I left my old prints in the system to try them, and they worked, but I did delete them and register new ones after that test). Print recognition is fast and doesn't take any extra pressure.Basically, after the pain of fitting, it feels like I'm working on the bare screen.

Easy to install but there wasn't enough adhesive liquid in the tubes. There were only a couple of drops in the two tubes that I opened which wasn't enough for the installation. I had to open the third one (which was full). So I have two screen left with no adhesive liquid for installation. The adhesive liquid has a very strong smell so consider doing your installation in a well ventilated room.Overall, the screen is good, feels like glass with a little bit of resistance when you use the S-pen. Screen protector is quite sensitive with touch but not as much with finger print (it takes a little bit longer, sometimes it takes a couple of try to work). It's compatible with cases. I'm happy with it so far but the lack of enough adhesive liquid and the smell of that liquid let me down, hence only 4 stars.