60” Demolition Pry Bar & Crowbar – Round Handle Wrecking Bar for Ceiling & Wall Demo – Heavy Duty Nail Puller Tool for Contractors, Firefighters & Home Renovations

As a demolition contractor the Guster 60” Demolition Pry Bar has been one of my favorite tools in my toolbox. Great tool and great product. Made with some heavy duty steel. Always gets the job done.

Great product, makes pulling up old hardwood floor so much easier. We waited to purchase this and struggled getting our old floor up, so glad we eventually purchased this, it has saved us a lot of time and trouble

Very good for demolition and sturdy

The tool has a bit of weight and it very solid. I purchased this to remove existing wood panel floors from a concrete subfloor for installation of vinyl planks. It worked great and took way less effort than using a hammer and crowbar. Not sure if this is just a defective item I received because the middle section of the foam grip was already slightly torn when I received the product. I didn't want to return it just for that and I needed to start demo so I didn't want to hassle with a return. The foam cushion on the middle section of the product started to rip and tear more after a few uses. I tried to wrap it with duct tape but the tape is also being pulled by the foam and is tearing. The foam grip on the top part holds up very well. After 2 days of use there are a few scratches on the teeth/bottom part of the product and the orange paint has chipped off. However, the product is solid/heavy and can take a beating.

As others have mentioned, this is a surprising tool that you should have if you’re going to remove hardwood floors if you use this tool on the tongue side to remove the hardwood floors, it is so easy it pulls and nails up along with the wood and if you took your time, you could even save a lot of the wood Well worth the money.

Works as described

I would pay extra for an aluminum version of this. Of course I'm just a 180lb weakling.

Works like a charm! Super solid. Ripped out 2000+ sqft of solid oak hardwood floors! Could not have done it without it!! 100% satisfied, would buy again in a heart beat

For serious demolition work this is the tool. The 48 inch bar was recommended by a contractor as the tool to use. I demo'd the interior of my 1957 house and couldnt have done it without the gutster. The house was built like a fortress but the gutster had an answer for every challenge. This is not a lightweight tool, but the weight is necessary to break through plaster, cement board and to loosen floor boards. I am 200 pounds , 55 years old and in good shape and using the tool overhead is possible but a workout ( ultimately it was the only thing that worked to take down a plaster ceiling with metal lath). On floors especially the weight is a plus. I used the tool to take down plaster walls, plaster ceiling with metal lath and wire mesh cornices, hardwood floors, 3 layer vinyl tiled floors, ceramic tile walls on cement and wire mesh, studs and frame walls, and built in place kitchen cabinets. The design is great. The flat bottom allows the tool to slide along a surface to get under boards etc. The notch on the head straddles 2x4s 2x6s to lever out stuck boards, the teeth on front bite into boards so you can pry them out. The notches on the back of the head were used to hook onto the plaster ceiling and pull down. The angle between the head and the bar was right to allow a good amount of pry on boards, while not bending over too much. The weight and the teeth were like a battering ram to break up the cement and wire mesh . A great tool and a must for demolition work.

Sehr stabiler Griff. Für meinen Einsatz waren die Zinken leider zu dicht.

I was using a regular crowbar to take up old deck panels - but it was very hard work as they were well screwed down (with screws that didn't want to be removed). So I got this and the difference is amazing - much less effort, much less changing position, much less backache and a LOT less swearing! Highly recommended!

Supposed to make taking pallets apart easy, but it's design means that it breaks more slats than it saves.

Last year we tore up hardwood flooring that was put in by someone who was paid by the nail. This tool got under the hardwood and lifted the flooring with ease. This year the challenge was to remove a large room with porcelain tile with not only the expected cement and wire mesh but it also had a heating system embedded in the cement. The demo bar easily lifted the materials from the sub-floor and I appreciated the weight as this helped drive the prongs deep under the mesh. Great tool. I'd recommend it.