CNCTOPBAOS K12-100mm CNC Router Milling Machine Rotational Axis A 4th Axis Rotary Table 100mm 4 Jaw Chuck Dividing Head,MT2 65mm Tailstock Reducing Ratio 6:1 for CNC Engraving Machine

I received a new 4th. Axis from the seller, and this one works fine!...Kudos to the seller for sending me a new one even when I was out of the Amazon’s return window. After I opened the box and manually tested it I realized that the new one was able to spin without much effort, opposite to the first one I got that it was hard to rotate, but since I didn’t know what to expect I thought it was fine and hard to rotate due to the stepper motor (I didn’t remove it). So here is my recommendation if you get one of these: Recommendation Once you receive your package, unscrew and remove the stepper motor (completely), as if you were trying to adjust the belt tension; this shouldn’t void your warranty as you should be able to adjust the belt any time and this is not opening the spindle. Now and without the stepper motor, manually rotate the spindle/chuck; the spindle/chuck should rotate freely, without much effort but not as a skateboard wheel; great if does. Even if you feel a small amount of friction it should be fine as it should be normal on these spindles/chucks. If you have a hard time rotating it (and hear something like a clicking sound) then you should be considering exchange it. Hope this helps. Note: I’m leaving my original comment below in case you were following… Original Comment: Disappointed!...The spindle it's barely turning and seemed to got stuck only after a few times using it. this happened right after my Amazon return window expired, so I contacted the seller for diagrams to see if I could open it and do some clean up or add grease, but they do not have any. The seller suggested to "hammer the inside four claws from the front to the back" but that seems radical and I'm not certain it will not damage completely the spindle. I have seen videos of other 4th axis that they have retainers/big nuts that you unscrew to open the interior, but this model has none; not in the back or in the front, and I have not found a site or video that shows how to open any of these models. Do not recommend. UPDATE 10/9/2019 The seller contacted me again and as there are no schematics available, then it's willing to help me solve the issue in a different way; by sending me a new product for testing and review, and have expedited the shipment. I'll provide new comments an possible update the overall rating once I have tested and reviewed the new product.

Really nice quality for the price! The motion is very smooth, with zero perceptible backlash. Unfortunately, I did have to return it. No fault of the product itself, but due to unforeseen controller issues on my end. The unit is very difficult to backdrive, thanks to the 50:1 harmonic drive. The NEMA 23 motors may look small, but it's no issue, again, thanks to the drive ratio. If you ask nicely, the seller will provide you with a CAD file of the unit to help with programming.

Not sure what the other reviewers are talking about there is a ton of backlash. Out of the box the belt tension is far too low. Even after adjusting that, there is way too much backlash to use this for a proper milling set up. Not sure what it’s any good for.

Very solid motor gearbox. I am pleased with the craftsmanship of this robotic joint and look forward to activating it in a robot arm.

Finally got around to hooking it up. The center is off by 40 thousandths! Don’t buy!!!

1. The rotary axis and tailstock were nicely packaged. Very well padded with foam. 2. No detectable backlash or lateral slop. This item comes with a 3A motor, which is sufficient but my drivers are 4A so to make sure I do not overload the motor I swapped it out. Another person who purchased this item has a long windy YT video about all the gyrations he put himself through to swap out motors. What he SHOULD have done is read the motor physical specs. My 4A motor fit in with no alterations required. The only challenge I have is mounting the axis to my router bed. I wanted the style that has a bore through the spindle so I can do pass throughs on smaller diameter items. This style has to have the motor mounted to the side of the spindle, so it limits access to the mounting bolt slots. I will probably make a sub plate because I remove this piece of equipment often. This is not a default, just something to be aware of.

I saw a review that said there were no instructions. If you don't know how to calibrate and install a stepper motor on Mach3 or whatever, you need to do some research. 6:1 is all that is needed. The synchronous four jaw check is great for center square stock.

Running this on a G0704 conversion with Centroid Acorn driving it. No issues, it's a solid unit and price is good.