Pullout Organizer for Cabinets, Min Opening Width of 15"

These slider shelves are the best! They are pretty easy to install and are a dream to have. No more bending down to look to see what’s in your cabnits. Very well made, sturdy, i cram my sliders full of glass canning jars and theres no sag on these shelves. Steel made and ball bearing greased rollers. A must have for any kitchen. No Chinese knockoffs here

I just finished installing these in seven of our kitchen cabinets as icing on the kitchen remodel cake. Really tired of getting down on the floor to pull out the heavy mixer or juicer from the back in the bottom of a dark cabinet. Pros: Nice chrome finish and fairly sturdy. I would have preferred the Rev-A Shelf birch wood units but too expensive for our budget. These are reasonable in comparison. Assembly of the unit is about 10 minutes. Cons: Installation took a couple hours for the first one. Maybe 20-30 minutes for each additional unit. Some things were not obvious. See tips below. Several assembly screws easily snapped off. Glad there were extras. My experience: The units are 1/2" smaller than the cabinet opening. I ordered for an 18"w cabinet opening and the unit is 17.5"w. That allows for clearance for protruding door hinges. The instructions said to mount the unit away from the door hinges (off center in the cabinet) which leaves a 1/2" gap on the hinge side. That side just stands in the air unattached or anchored. Being off center bothered me. I would need to add some kind of blocking to move the units to a centered position. In my case I also ordered the door mounts to convert the doors from hinged to a pull out configuration. That's where my confusion started. The door mount brackets were off center from the doors position directly below the drawer because the units were installed off center. I didn't have enough door frame to mount the door that off center. There are round discs (spacers) included with the door mount bracket kits that will allow you to move the brackets left or right but it looked odd to me. I realized that I could use the round discs (spacers) to center the whole unit by using the spacers in between the unit frame and the door frame on either side. The four spacers provided at the four front anchor points. I had to provide longer screws to make this work. The result was a centered unit in the cabinet opening with a centered door pull. See pictures of the spacer positions. Tips: 1. Hand tighten the assembly screws. They snapped easily with a screw gun, even with the drag set low. 2: If you are installing the door brackets (separate kit) use the spacers to center your unit in the cabinet opening rather than off center. See pictures 3: Install the drawers so that you are sure the brackets that attach to the back of the cabinet are truly parallel and won't bind the drawer slides. Mark the holes, remove the drawers and mount the rear brackets. Then attach the unit to the bottom/base with the four screws provided. 4: Mounting the door to the brackets: Attach the brackets to the bottom drawer. Tighten the screws just until the brackets stay in place but can still move if pushed with some force. Apply the the double stick tape to the bracket faces. Pull the drawer slightly so that it just sticks out beyond the cabinet face. Line up the door panel under the drawer face right to left and also the door top down from the bottom of the drawer face. Press firmly in toward the brackets so that the brackets adjust from the pressure and the double stick tape adheres to the door panel.. Carefully open the door/drawer and attach the screws. Note: The instructions said to face the brackets outward. This did not work for our doors so we turned them inward.

These pull-out shelves are AWESOME!! They were surprisingly easy to install, feel very sturdy, and completely changed how usable my cabinets are. I can finally pull everything out and actually SEE what’s stored in the back instead of digging around blindly. They also seem to create more usable storage space because everything is organized and accessible now. The sliding mechanism works smoothly, and the quality feels much better than I expected. If you’re tired of losing things in deep cabinets, these are absolutely worth it!

I had hesitated buying ready-made wire cabinet drawers thinking that I would make my own. Silly me. I should have bought these years ago. They are a perfect fit in our 40 year old base cabinets that I've refinished twice. The first picture shows both the upper and lower drawers installed and retracted. You'll get a glimpse of the jumble in the part of the cabinet next to it. That is how our kitchen cookware used to be stored in the left part. The second picture shows the lower drawer opened, and the third picture shows the upper drawer partly open. The fourth picture shows one of the No. 6 hex head screws that I used for installation. The screws that came with the sets are perfectly fine phillips head screws. But my early years in mobile home service made me appreciate hex head sheet metal screws! The fifth and sixth picture show the right angle drill, with the driver extension that I used to drive in the screws. All in all, once I gave the inside of the cabinet a quick cleaning and a coat of waterborne varnish, installation of both drawers took less than 15 minutes! The instructions that came with the drawers are good. You won't need the power tool that I used but it's helpful. You can drive in the screws by hand. We are getting old to the point where it hurt to sit down on the floor to plow through the cabinet to find things in the back. Cleaning out the cabinet was like a trip down memory lane, finding things missing for 20 years like a missing wide-neck funnel and a saucepan that had belonged to my wife's grandmother. Do I recommend these wire drawers? Bodaciously yes! You may lose some cubic inches. But you will make that up in useful cubic inches.

Very easy to install. Very convenient to use in deep lower cabinets.

This product will be used in our kitchen base cabinets (2) for pot and pan storage. The default cabinets in our new home are the typical empty bottom base and half-width shelf midway up. We find these generally useless and difficult to access at our (retired) age. The cabinets have face frames, which is typical of base cabinets here in America. The overall design and quality of the product is excellent. The various parts are manufactured with good precision and provide a stable solution for us. HOWEVER, whoever thinks one of these can be installed in 20 minutes must have been smokin' something when they timed it. Either that, or it was timed after 50 installs in a perfect cabinets! The problem that I faced was that one of the steps required using wood screws to fasten the sliders on one side to the edge of the cabinet "face frame" on that side. Unfortunately, the edge of the slide MUST be at least 1/4" back from the front of the frame. If this is not done, then the cabinet doors will not close completely even when the baskets are completely closed. But the center of the hole used to attach the slide to the frame is 1/2" from the edge of the slide, for a total offset of 3/4". In our case (probably the norm for newer cabinets), the face frame itself is only 3/4" wide. Thus, there is no "wood" left to grab the screw. My solution was to fasten a 2x2 furring to the cabinet wall behind the face frame, and then fasten the slide to that. Before doing so, I checked out the solution with the manufacturer customer support staff. They not only agreed that it was just about the "only" possible solution, but that many other people have called with the same problem. One must wonder why they don't either include relevant parts and instructions, or change the design slightly to avoid the problem (i.e., just move the whole in the slider forward by 1/4".) Hence my poor "ease of installation" rating. The picture included above shows the final installation.

We bought our house in July 2024, and got these for our cabinets installed 5 months later. It made all the difference in the world. Downsizing to have a smaller house really took a toll on us in the kitchen area, and we really suffered from not have all the storage we'd had before. These shelves are wonderful! I use them every day, and thank my lucky stars every day that we had them installed. They pull all the way out, allowing you to get whatever is in the back without pulling out half the stuff. I very rarely have to get down on my knees to get things out of the back of cabinets--and at 77 years old, that makes a huge difference to the quality of our lives!

These Rev-A-Shelves are absolutely amazing! I started with one and now have a total of nine. There is no way you can organize a kitchen cabinet like you can with these pull-out shelves/drawers. Without these shelves, stacks of bowls, pans, condiments, cans, etc. will fall over. Also, items get lost in the back of dark, deep cabinets. These Rev-A-Shelves are deeper/have higher sides than some other makes/models, thus allowing for better organizing where items stay in place. For the shelf under my kitchen sink, I put a plastic basket in the Rev-A-Shelf to hold house chemicals. This way, if there should be a leak, it will stay in the basket and not leak through the wire shelf. And for my pantry, this shelf is big: 24’ x 22. I also put another plastic basket (about ¼ the size of the pull-out shelf) to separate smaller items (Jello, condiments, etc.) from larger items such cans, etc. TWO HUGE factors to check when looking at other makes/models: the Rev-A-Shelf brand shelves have FULL EXTENSION. All the others have ½ or 2/3 pull-out extension. This is not enough and allows for wasted space in the back of your pull-out shelf. Also, the WEIGHT LIMIT is 100 lbs. I think it would be rare that you would have anything that weighs anywhere near 100 lbs, but this lets you know the quality and stamina of the way these are built. These shelves come packaged extremely well with lots of packing/styrofoam, they are built solid, are heavy and great quality. They are lubricated and roll in and out of the cabinet VERY SMOOTHLY. If you can’t find the exact size of the shelf you need and are tempted to look at other brands-- DON’T! These shelves are worth losing an inch as opposed to buying another brand to get an exact fit. Sometimes when you order items like these, there are screws missing or the screws aren't the best size. All the screws for all these 9 shelves were included and are the perfect size. No need to buy any other size screw. Here is Rev-A-Shelf’s website showing the various sizes: https://rev-a-shelf.com/2558? This makes it easier to see the all the sizes they make. Then you can take the model number of the shelf you like and plug it into Amazon’s website. Some of these were received a day or two after the actual due date, but not a big deal at all. Rev-A-Shelf communicated the delays. If the due date was a month out, it would absolutely be worth the wait. Nope- I don’t work for Rev-A-Shelf and I did not receive any of these shelves in exchange for a review. Just started with one to organize my 2-ft deep pantry and saw how amazing these pull-out shelves are! You can actually fit more in a cabinet/pantry with these shelves than without. The ONLY two specs to look at if comparing other brands: 100% FULL EXTENSION AND WEIGHT LIMIT OF 100 LBS!

Works perfectly!

The double shelf was well constructed, sturdy and easy to install. It totally solved my problem. I had a 12 lower cabinet that was accumulated "stuff" which I could not get to even if I had wanted to. Now this space has become useable. Easy access to all items. The racks slide out completely from the cabinet. Great investment. I now intend to purchase more rev a shelf items to maximize my cabinet space and make easy access to items. Inspired me to reorganize my kitchen space! Definitely recommend this product.

Very sturdy and works well

I was impressed by the easy to follow instructions. The added support to attach to the bottom of the cabinet is something the cheaper models don't seem to have. This shelf is solid and is built to hold weight. I also ordered a door kit assembly; however it is good to note that you need two, one for the top shelf and one for the bottom. Great product.

We bought it for our camper. We installed it in the outside kitchen and we put a grill on it. The shelf works great and extends completely allowing the grill to be a few inches from our camper. It was a great solution for us to add a grill and have it easily accessible. The shelf has no difficulties sliding with the load of a grill. I would definitely recommend this grill.