565 Multi-Purpose Cutting Kit

Got it to cut out my plastic electronic project boxes. Great addition to my Electronics Laboratory Bench. I also like the depth gauge it has and that it came with three cutting bits. It also works with my Dremel Chuck.

Bought this instead of an actual drywall cutout tool. Just for use in a semi large diy project and didn’t want to cut a bunch of outlets by hand. Worked great. It’s a bit slow but still faster than if I’d done it with a hand saw and it makes some very nice clean cuts. Ended up using it a 2nd time to cut an outlet to mount a tv. It was perfect for job. If you only occasionally have to cut drywall and already have a dremel tool this is a great addition. Very easy to control, a little messier than a hand saw but far quicker and easier than hand cutting.

works great

I bought this set mostly for routing purposes. I needed to attach a routing bit and a guide to my Black and Decker RTX rotary tool, and this fit the device perfectly. used it to carve out the hinge area on new doors for the apartment that I was renovating. The bits were the real bonus! Ultra strong and able to resist breakage. I mainly used the all purpose one. I needed to trim off the bottom round feet of a new Belle Foret vanity cabinet that i recently bought (http://www.amazon.com/gp/product/B00GHWRVRK/ref=cm_cr_ryp_prd_ttl_sol_7). The problem of using a saw is that I would need a vise to hold it down. And since I didn't have a vise laying around I figured this Dremel bit would do the job...and did it EVER! It cut extremely fast right through it without much pressure. Had to be careful while holding the round wooden foot. Of course it wasn't a perfect cut, but that was fixed with a sander. I don't think any other bit would have held up. This bit got very hot, but never disappointed.

Since this is a Dremel product, I expected top quality and that's what I got. I especially like using this for cutting away sections of 3/4" drywall without having to worry about cutting through electrical wires or copper water pipes. It will cut EXACTLY to 3/4" if you very carefully set the bit depth and you have smooth walls to drag the support across as you cut.

Just as advertised.

Does not fit newer models of Dremel

A great addition to my Dremel accessory collection. It allows a consistent depth of cut and has a wide open side so y9u can actually see what you're doing. I would not depend on the measurements on the adjusting collar, but make your own. It's real easy to install just by removing 2 parts from my rotary tool and screwing it on. It is made of plastic, but it should last for years. I have not tested how many bits you can use with it, but the 3 bits it came with seem to function normally.

Nee. Das hat nicht so wirkungsvoll funktioniert. Der Schneid-/Fräseffekt war für das Holzteil zu gering.

Very good and a fair price. Thanks.

Great item, does exactly what I want from a reputable seller.

ドリルで木を切れるんかい フリーハンドならベニヤ板に対するジグソー代わりかな？ と考えていましたが 木切れのガイドをセットしてやると円の中央にドリルが来ますので バッチリな直線の切り口が得られるルーターのように使えます。 いつもガイドの取り付け固定方法には悪戦苦闘しますが、ここが最重要 これを知ってから最後の仕上げには欠かせない道具になりました。 空中からドリルのように回転させて部材に接触させると持って行かれます。 ガイドの縁を接地させてから斜めに歯を入れろって説明書を理解しました。 最初斜めでも切れるっていう感覚を持っていなかったのでやっちゃいます。

This gives my Dremel rounter extra capability, on my small projects.