Finish Line Premium Grease made with Teflon Fluoropolymer, 3.5 Ounce

Have used this on everything from bearings, screws and seatpost stems to keep them from seizing together. I would not recommend using it on the girlfriend, it will not loosen her up or stop the squeaking.

Of course you can buy grease in bulk more cheaply, but this is a good quality grease in a convenient squeeze tube. I don't have a small grease gun sitting around and I'm not a professional mechanic, so this does the job. At the rate I work on bikes, it will last me for years. Bikes generally don't take huge amounts of grease, so convenient dispensing of small amounts is more valuable than the cheapest price for grease.The grease itself is white.

I'll begin by saying that I though this grease was excellent. I've used it in several skate and bike bearings and it seems to do it's job admirably (though it's quite hard to compare effectively to cheaper alternatives). Since I can't effectively compare it's function (meaning all the options are reasonable) I'll talk about it's usability, other than to say it seems to work well.First of all it is very sticky. This is a double edged sword. This means that handling it is tricky but it also means that one can more readily ensure a certain surface is fully coated with a thin layer. This is in contrast to packing then spinning to push out excess of placing several "blobs" and relying on motion of the part to gradually spread the grease.Secondly it has an extremely smooth texture. This means that, if you apply it suitably thinly, there is very little in the way of "break in period". This means that if well applied your bearings will be rolling optimally in short order.Thirdly comes resistance to dirt. Despite the sticky surface (which does attract dust) it doesn't seem any worse than any other grease I've tried in unfavourable conditions. That means that any dirt that reaches the lubricated surfaces will eventually cause problems but some such dirt touching lubricant away from the surface should not be problematic.Forth comes the container. This is the only real problem here. I purchased this grease along with the  Finish Line Grease Injection Gun  and initially this worked great. It allowed for delicate application and reduced the mess caused by the sticky texture. The problem I had, however, was after a few uses the neck of the contained snapped and I was left with a tube without a screw thread (that could no longer take a cap or grease gun). It's hard to say whether this is the fault of the gun or the tube but in either case it is frustrating.Overall this grease met my needs and, barring the problem when used with the grease gun, it seems to work well.

I purchased this after reading about many user experiences with the Schwinn IC4 and issues with the pedals stripping. Someone online recommended to place Polylube 1000 on the thread before installing it to keep the pedals from stripping out of the crank arm. I followed that advice, purchasing this bike lube instead and so far I've had no pedal issues. Hopefully that remains the case but so far this stuff seems to have done the job.

Received in a quick manner thank you Amazon Prime. Upon opening I noticed that only half the tube was filled. Not sure if there was suppose to have a seal on the tube after removing the top because mine did not. But receiving half a tube of grease seems pricey for what you get which is why I knocked off 2 stars. I used this to rebuild my bike hub bearings and the grease feels like butter. The ride is smoother and free wheeling has increased. Hope it lasts.

This is a pricey grease compared to what you can buy for your car or boat which work just as well but I thought I'd splurge and get it for my bike because I don't grease the bearings often and wanted something of high quality and got this.I used it and had some left over in the tube but when I tried using it 8 months later, it had gone bad! It was separated with a yellow oil pouring out first like in a peanut butter jar. I can only imagine how bad it is in the bearings now.

Excellent well worth the money and I am extremely happy with it best bicycle grease on the market the only grease I will ever use on all my ebikes and I put high mileage and it hold's up

I bought this to use to grease up my 3D Printer, primarily for the Z axis screw rods (i have a dual Z axis screw rod setup) on my Ender 3 v2. While this grease does work for that purpose its a very thick grease that is a bit difficult to spread over the grooves of the z rod. I've also used this grease for extruder stepper motor gear, which also worked ok, but again was difficult to spread. I would look for a different grease for use with 3D Printers.

Using this to lubricate my Bikes Crank. Works like a charm!

I use it for most greasing jobs on my bikes. I ride almost exclusively off road, often in wet and muddy conditions. This stuff does the job. I will carry on using it. Still on my first tube - this stuff goes a long way.

Tried and tested before so I knew I was getting the product I needed. Used by the many other cyclists I know so it is a great purchase. Does everything you need and lasts well through the winter.

its good

Good stuff for a decent price.