BullRing Retractable Truck Bed Tie Down Anchors, 2-Pack – Centered Stake Pocket, Flush Fit – Fits 2015-2026 Ford F-150, 2017-2026 F-250/F-350 Super Duty & Raptor

These are a little expensive, but I'm beyond impressed. Exact fit for my new 2019 F150!!! (no cutting, no drilling, looks like it was installed by Ford) Extremely well designed, and as an engineer the little details stand out. Very well made. Stainless hardware with brass thread to prevent binding. The tie-down hook locks into place when you pull up on it making it easier to install straps, etc.. but then a small push down and it releases. (No fancy mechanism to break over time, just a simple pin under neath that clicks into a smaller indention.) The molded plastic is high quality, and they even took the time to add the exact same texture to the top as Ford has on their plastic bed rails along the top. (literally looks like the union UAW guys installed it at the Dearborn Truck Plant) Texas designed, fabricated overseas, but well done. Even has a small fish design under bull ring which speaks to this companies integrity. I would highly recommend and would buy again in a heartbeat!!!

These work great and are super easy to install.

These were easy to install on a 2020 Ford F-150 XLT 5 1/2 ft bed. Additional tie down anchors are always welcome. I may never use them. I'd rather have them if I need them rather than need them and not have them.

For those who aren't sure of what offset means, basically that means that the hole is not centered in the top of the plastic top rail. In my 2023 F150 the front 2 stake holes (by the cab) were slightly offset about 1/8 of an inch (see picture). According to the manufacturer, the offset rings are offset by 1/4 of an inch so what do I do with an 1/8 inch offset? So after an email and a quick response from Bull Ring USA, they suggested I try the regular fit first, if they don't fit they will replace them for free with the offset version. I ordered them and first tried to install them with the Bull Ring logo toward the rear of the truck. No dice... they were not flush and sat on the top of the plastic rail. I then flipped them around with logo toward the cab and viola, perfect fit! Nice and flush. I bought another pair from a different company but the Bull Ring's in my opinion are a little nicer. The fit and finish are top notch. So my advice is if your hole is offset by less than 1/4 inch like mine, go with the standard and if they don't fit at first try, then flip them around before you tighten them up and see if that gives you the flush fit. If not, their customer support is excellent! I really like a company in the USA who answers their phone and email. Highly recommend!

Fits my truck perfectly, although it did take me a few tries and watching the video to figure out how to install it. The second one took about 30 seconds to install after I learned how to do it. Exactly as described and so handy. Seems very sturdy.

My truck sets up high and to reach over to tie anything down to the factory anchors which are more toward the bottom of the bed is very difficult. Found these anchors after doing a little research and decided to give them a try. I am very pleased with the purchase and the functioning of these anchors. I haul lumber and other items that extend past the tailgate and run a bungee cord from one anchor to the other side bed and it works fine. These anchors then snap down and are flush with the top of the bed. They are easy to install. The ones offered by the manufacturer were $20 higher and made by the company that makes these.

My 2018 F150 came with a Back Rack installed. When I removed it, I was left with holes. Luckily the holes were just in the plastic bed cap. I cut the stake pocket out with an oscillating tool and installed these. They obviously don't mount flush, but they look much better than the holes. My only complaint/wish I guess is that if they came with a simple rubber gasket, they would look more like they are supposed to be on top of the plastic. Not the manufacturers fault because they tell you what it is, but a couple of cheap gaskets to allow for more applications would be amazing. I knocked off a star because they say "snaps up and snaps down". They snap in place when up, but down they just kind of hang.

Wonderful purchase! I was tired of popping out the plastic covers to access the tie down points on my truck bed. Installation took 2-3 minutes for both of them combined. They work, fit, and look perfect! I wish I would’ve bought these sooner. Highly recommend!!

Buena calidad, parece producto original de FORD

Amazing product

Work just as advertised! Awesome fit and 30 seconds to install. For those of us in cold climates... Know that they will likely be frozen in place. Not the product's fault. Sturdy build, super happy.

En el video de instalación muestran demasiado fácil el proceso de instalación pero las medidas del producto hacer que no entre fácil, por lo menos en un modelo 2017. Tuve que cortar un poco del plástico para lograr que entrara. Una vez instalada han sido muy útiles y buenas.

Very easy install, takes about 30 seconds to install. Feels like it's quality-made. I'd buy it again but hopefully will never have to! :)