POWERTEC 70169 Mini Gulp Dust Hood Collector with 4" ID Port - ABS Plastic Fitting for Woodworking Dust Collection Hose

The chute js a great size and quality. Works great on my wood Lathe.

Great piece for dust collection

Works great! I use it as a dust collector for my radial arm saw.

I do a lot of knife building including making handles., grinding blades etc. I frequently use a die grinder with carbide rasps and a Foredom flex shaft grinder also with carbide rasps and bits for roughing out handles. Those tools work great but they make a big mess. This collection hood is the right size but the wrong configuration. By itself, the hood is too light, inherently unstable and difficult to use as is when it arrived due to weight of the heavy vinyl hose from my Jet dust collector. I made a frame for the hood for bench top use that dramatically improved the usefulness of this dust collection hood. The frame gives the hood some weight and stability on my bench and I can clamp it to my bench or wherever when needed. The setup works very well for my purposes and I collect about 70% of the dust with my 2hp Jet dust collector connected. Hard to go 5 stars considering the modifications required to meet my needs but for the price, it’s a lightweight and now well designed & functional + portable dust collection hood. I plan to add a handle to my Jerry-rigged dust hood concoction. Your experience and needs will inevitably vary and the hood might work perfect out of the box. Hope that helps!

I use this under a wood lathe to pick up much of the dust and falling chips or on a bench when sanding. I've dropped this more than once and and it did not crack or break.

I have a Craftsman 10” saw that I have been using for over 30 yrs. Since retiring it gets almost daily use. The amount of saw dust produced was becoming a major time eater cleaning it up. This item fits the saw base perfectly, I decided to mount using industrial 2 sided tape and it took literally 15 minutes to install I already had a dust collector with 4” hose so attaching the vac took 5 minutes to install It leaves a small amount of chips around the edges but nothing bad of to be a concern. Every so often I just turn the vac on and use air hose to clean any minor buildup around edges

This hood worked as advertised once I got it installed. It was literally a pain in the neck to install on my Delta XL-10 table saw, although this was not due to any short-comings of the part itself. I tried to be too clever, and painted myself into a corner with the installation approach I used. It was too small to simply bolt on to the bottom of the saw housing. So I cut a combination mounting ring/spacer to size from 1/2" plywood and cut out the center (leaving a square "ring" of plywood), to which I then attached the hood such that the hood would be on the "inside" (i.e., the hood will hang from the plywood ring by its 1" offset lip). At this time, I also attached an adapter to the outlet port (POWERTEC 70136 4 Inch 2 Inch Reducer) so that I could connect my shop-vac to the hood via a permanently installed hose. I screwed all the parts together, adding a bead of caulk to all mating points to prevent leaks. I then let the caulk cure before installing the assembly onto the saw (which I had already unbolted from the stand). Unfortunately, with everything in place, I discovered that now I couldn't reach the bolt/nut locations inside the saw housing (my new hood assembly was blocking the previously wide-open bottom of the saw). Although I did have enough forethought to get longer connecting bolts and to pre-drill holes in the plywood ring, getting the bolts to feed down through the holes from inside the saw housing was problematic at best. After fighting with it for a couple of hours, I was able to get three of the four bolts tightened to my satisfaction. I cheated on the fourth one - I used a drywall anchor and fender washers to get it snug-ish. I added caulk to the mating surfaces (saw-to-plywood, plywood-to-legs) before tightening the bolts. The bottom line is that, in spite of my dumbassery, the hood and adapter work as expected. Some dust is still escaping from the standard clearance plate, but it is much less than before installing the hood, and nothing is coming out the bottom. I do need to seal up some other spots on the saw housing, and will probably switch to a zero clearance plate - howver, I am already very happy with the results thus far.

It is plastic, but it is made well. Very happy and recommend.

رائع في جمع المخلفات

EL MATERIAL ES BUENO Y EL TAMAÑO ES PERFECTO PARA RECOLECTAR MÁS QUE POLVO DE MI SIERRA.... ESTOY MAS QUE SATISFECHO CON MI COMPRA...

Stabiles Material,brauchbare Größe,gutes Preis-Leistungsverhältnis kann ich weiter empfelen

Il faut tout de même un énorme système d'aspiration pour qu'il soit efficace.

Sizes and packing also good