BETAFPV F4 1S AIO Brushless Flight Controller SPI Frsky FCC 5A ESC Integrated 25mW VTX with BT2.0 Connector for 1S FPV Brushless Whoop Drone Like Meteor65 FPV Micro Whoop Drone

I used this flight controller to replace a burn out one in my cetus pro. It was rather dificult, so this is a detailed guide to getting it running.Flashing: the correct firmware to flash to this flight controller is MATEKF411RXBinding:Flight controller setupthe flight controller can be run on any of these protocols, but it needs to be set up under the configuration/receiver tab1. set the top box to "SPI RX support"2. to change the protocol change the lower box, following this chart:FRSKY_D = FrskyD8FRSKY_X = FrskyD16 FCCFRSKY_X_LBT = FrskyD16 LBTSFHSS = Futuba S-FHSSReceiver Setup (transmitter BETAFPV 2SE)If you are using a different receiver, check see what protocol it's on and change the flight controller to matchTo change protocol of the betafpv 2SE1. Hold down the bind button and keep it depressed as you turn on the transmitter (do this until you are on the correct version)**to see the current version, turn it on normally, use the chart below, looking at the number of red flashes before the blue comes on to determine the protocol**One Flash = Frsky FCC D16Two Flashes = Frsky LBT D16Three Flashes = Frsky D8Four Flashes = Futaba S-FHSSActual binding:First off, after reading other reviews, I would suggest the Frsky D8 protocol1. get flight controller in bind mode-connect to Betaflight configurator-go to receiver tab-at the bottom right click "bind reciever"2. get the transmitter in bind mode (BETAFPV 2SE)-turn on the transmitter-press and release the bind button (do this multiple times if it didn't work the first)-wait five secondsI strongly suggest following this video and referencing these instructions as it goes:https://www.youtube.com/watch?v=xmaTq4JgTXIOther helpful links:https://betafpv.com/collections/tx/products/literadio-2-se-radio-transmitterhttps://betafpv.com/collections/brushless-flight-controller/products/f4-1s-aio-brushless-flight-controllerHope this helps!

You cannot unlock VTX, it won't over R6, meaning, you will have messy signal due to Wifi interference.

When I got this board I plugged into my computer to update the firmware I picked betafpvf411rx did update and nothing would work watched a video from cyclonefpv showing the firmware is not betafpv it's matek so I updated to matekf411rx set the uart ports 2 to vtx irctramp receiver to frsky_d for d8 tried frsky_x for d16 had horrible range then set your modes arm,angle, horizon, beeper,flip over after crash save that make sure you set them up on your radio also then you gotta set the camera angle to 30 arm angle 180 give it a name set the board to flip 90° and then other one under it to flip 90° also then reboot do your z axses and level out your accelerometer go to your vtx download the files for channels load those after you save them somewhere setup your channels I have fatshark chanel 4 the vtx power output to 25mw since that's all it's got save that go to your osd settings set that how you want it best to have your goggles on so you can see where everything is make sure it's where you want it save go to motors set reserve motors dshot300 bidirectional on save that reboot plug in a battery re order motors make sure there spinning right way if not reverse them one by one once those are good save disconnect and fly 🤙

I put one of these into my Meteor65 Lite because the original esc was fickle about spinning up all 4 motors. It was easy to set up in Betaflight. I found that using frsky D16 wasn’t reliable because it was getting random Rx loss. Switched to D8 and it’s solid as a rock. Really good AIO for the money.

Works well. Made a moblite 7 copy with better parts. Down side, 25mw vtx. Great for whoops or small toothpicks.

Not for beginners. Had 2 delivered and both had bad gyros....

This is a mixed review as I've gotten 2 of these FC that had an issue and also ordered 22000kv motors but received 190000kv...thankfully Amazon has exchanges and returns in place.I have 4 other betafpv quads and I have not had any problems yet and one is a year old. This makes me unsure if it's betafpv's quality control for this product or the way Amazon handling these things that caused the problems. I know this is a great FC and will be getting some from a fpv shop instead.

This great F4 FC from BetaFPV has the ESC, the RX (Frsky), and the VTX all build into one board! It is awesome because with this FC you can put together a full whoop build without soldering any soldering required! It was super easy for me to set up because the RX and VTX are both built into the one board so I just plug in a camera (I used the BetaFPV C01) and the motors also just simply plug in and that's it your build it complete! This board is ideal for any lightweight whoop builds, especially for both 65mm 1S freestyle and racing I highly recommend this board. Some other notes, I am glad that the VTX antenna is attached with a UFL rather than soldered on so that you can change antennas easily. I use a the lightweight diploe for racing builds and a clover/omni antenna for longer range and explorer builds. This is currently my favorite board for any 1S 65mm whoop build.

Ormai non ha più senso comprare questa fc, costa come le moderne con elrs ma il range anche dopo aver eseguito l'rf fine tune é adatto appena a volare in casa, e non permette di montare crossfire o altre riceventi esterne. Il bind a patto di scegliere il giusto protocollo radio é easy.Regge BF 4.3 con pidloop a 4khz ma ci si brucia molti vantaggi a causa della latenza del protocollo radio. Su frame in carbonio come flywoo o Verbena sopporta valori di filtraggio veramente minimi, é compatibile con Bluejay e in generale é soddisfacente, ma a mio parere meglio orientarsi su fc più moderni, come il nuovo betafpv "a croce" con elrs integrato.La vtx integrata funziona molto bene, con una buona antenna anche a 25mw finisce sicuramente prima il link radio di quello video.In generale non lo ricomprerei sempre a causa dell'obsolescenza.

El producto me llego con un fallo en su motor N3, tampoco me gustó el gyro elegido icm20689.

Order for the second time and Ince I connect the camera to the fc is burn.

Fonction parfaitement sur mon meteor 75.La fc et plus légère que celle d'origineCar le vtx et intégré.Au top, Avoir dans le temps

Montage relativ einfach, Einstellung über Betafligh geht auch Recht schnell. Achtung FrSky lässt sich nur mit alter acces 1. FW binden. Schön wäre ein beiliegender Stecker/Kabel um eine vorhandene Kamera leicht anschließen zu können