AECOJOY 10'×8' Manual Retractable Awning Sun Shade Patio Awning Cover Outdoor Patio Canopy Sunsetter Deck Awnings with Manual Crank Handle, Beige

Product came on time was packaged very well, etc. etc. All the parts were there, and I highly recommend that you look at a couple of YouTube videos before attempting to install. Also, follow the instructions to the letter very carefully. It’s also key that when you first roll the canvas or cloth, That you roll it tight, and keep the swivel arms tied together and bound, so it’s easy to manage when you first put it on the brackets to the side of your home. It is most definitely a Typical two person job. That doesn’t mean that you cannot do this on your own, but it will take 2 to 3 times longer than if you had an extra pair of hands. OK, so here is the lowdown: You need to make sure that this is attached to either a stud behind the outside wall or, you need to build this out in order for it to be firmly secure. Mine is under a gutter, second floor, high-rise deck. The brackets are made of steel and Are assembled long ways, so the bottom half has nothing to attach to since it is under the gutter and the facia extends out with no support. So what I had to do was to cut Pressure treated 4 x 4 posts, attached it to another pressure treated board to build it out past the gutter. It is well supported with 4 inch lag bolts that go directly into the facia board that holds the gutter. If you don’t do this, that assembly will either rip from the house or, it will fail in high winds and come crashing down. I used flexseal white paint to cover to match and heavy duty foreign screws to make sure that during winds that the assembly will hold together. It took me a few more hours and expected, but the roller has to clear the gutter or you will not be able to extend and contract properly because the gutter is in the way. I honestly wish they had an extra extension bracket that was about 4 inches that came with the Product because it will cause extra work to the typical homeowner. Also, I highly recommend at the end of the canvas assembly, which extends out to snap them in, they will not hold. Go get either gorilla glue or heavy duty gorilla Adhesive caulk and lightly coat those pieces before inserting into the grooves so they all hold together. Reason being under at times stress when the canvas is shifting because the wind they will tend to pop out. Good luck, trying to find them in the cracks of your patio bricks, or in the grass down below in my case. As with the fit, it extends out perfectly and it retracts very smoothly. The canvas is made with good quality so I do not see this ripping or tearing anytime soon. We have had 15 to 20 not wins and it holds up very nicely. The crank is easy to maneuver and it is made of solid steel frame so I do not see this in the wind as well. We had some slight rains, and it did work as intended, which is key because I barbecue quite a bit and it’s nice to not be rained on while I’m cooking outside. As a sidenote, this does not come with a campus cover for the housing when it’s rolled up. I highly recommend that you purchase an additional campus cover so in the winter or whenever you are not using it for a long period of time that it is protected from the elements while it’s outside. I found one here on Amazon, which is about $46. This will come in handy in the late fall in winter during the Chicago weather. Overall, and quite happy, but just make sure you set aside enough time to have this completed properly. I would say for the value, it’s a very handy product, especially when you’re out side, entertaining, or just enjoying a cuppa coffee in the mornings. So much better than having, one of those umbrellas that you have to continually crank which can be quite cumbersome and honestly a real pain to set up. So again, make sure you have enough time to make sure that this is assembled and set up properly. This will take approximately about a half to a full day to complete if you want to do this right. As in the pictures, you will notice I do not have it extended all the way out. It is OK to do that. It won’t harm the brackets. It can extend all the way out approximately 10 feet which goes over the deck and the stairs going down. I just don’t need it that far, but I have the ability to do so if I would like. (Good Luck! It’s very well worth the investment!)

Easy to install, makes the deck much more useful by shading direct Sun and much cheaper than most awnings

I do have experience with awning but this is really not worth the or the time. It’s very light weight & low quality. Opened the box . one of arm are bent. Started to assemble the awning. one of the brackets are missing & one of alien screws get bad after tightening up & wont be able to un tighten back. I did requested a return. they sent me the return address & asked me to pay for the shipping cost , which will cost me tons of money. I contacted Amazon and explained the issue & they told that they will contact the seller, but the seller refused to solve the issue. the did contacted Amazon again, the told that they will use the so called ( A to Z Amazon policy) which will result in covering the return shipping cost. I just received an Email from Amazon that because the product is not from Amazon , they cannot resolve the issue & I should pay for the shipping. I will try to contact Amazon again to see if still the issue can be resolved.

Great product for the price, by terrible instructions!

Great product ! Very well engineered. Assembly does take some time and I would suggest two people to install. Heavy duty frame and fabric. Extremely pleased with this product.

The assembly instructions left out several important bits of information, but we were able to figure most of it out anyway. After getting it put up, it works wonderfully. Really good quality and seems solid and sturdy.

Beautiful awning. It’s well made and heavy material. It’s not hard to assemble. A bit tricky but not hard. Love it

Ended up buying this product because it was well priced and had decent reviews. Spent about three hours assembling this with a partner and I have to say this is one of the worst instruction manuals to have to follow directions on and I’ve been assembling products for over 15 years. Upon completion of the assembly with noticed, that one of the arms was hanging lower then the other. having made all possible adjustments, trying to fix with no luck I contacted the seller for help. They essentially asked me to do everything that I’d already done as instructed in the manual and eventually said it’s my fault for not being able to adjust the arm. In reality, there’s a loose pre-installed unadjustable screw that is on the arm in question. That is the main issue here but the seller refuses to take fault on shipping me a defective product.. I would strongly advise to stay away from this product and save your yourselves the headache and money.