Heavy Duty Metal 2 Hole Punch - Up to 65 Sheet Capacity

this is a great punch is made by Office Depot and it does the job. It is an All metal punch so it should last (parts that are not metal is a coating of plastic on metal handle, the plastic base like all hole punches (this opens easy and is easy to clean out) and the lock to lock the handle down this is plastic but is strong and i don't see it braking unless someone forces it!, It also come with a paper guide ( Position guide) for the paper which does a mix of paper sizes (A3, A4, B4, B5, B7, B6) Ill end on the price, this punch in other office shops sells for around 25 GBP. So this (at the time of review) is a good price! Im also going to try upload a photo of it as i found the photo on amazon not to be as good is i would have liked. (In the photo ive noted the size etc of the punch)

This product has helped save a lot of time. It is robust and does the job perfectly. Much better and a huge time saver compared with using the standard hand-held hole puncher that allows you to punch only a few sheets at a time. It has a lock mechanism, allowing you to push the handle down and lock it in place for easy storage.

Not expensive, but probably not the punch I need. It is very heavy, and there are problems with it: Although the guide arm is metal (my main reason for buying it) the guide arm retaining part is too low. It barely allows you to align anything more than a handful of pages. Secondly, for me, the holes are slightly too close to the edge of the paper, only 6mm. Thirdly, where the area the paper is pushed up to, inside the jaws of the punch, it has two small metal tabs, presumably as part of the construction, These two tabs are about 4mm wide and do not reach the top of the space against which the paper is held. This leads to two problems: firstly, as there isn't a clean wall of metal to push against, there is a tendency for the paper to wobble within the space meaning the holes are often at different depths from the edge of the paper; and secondly, if punching a really big pile of paper, the lower sheets are punched closer to the edge of the paper than the higher ones. Fourthly, the notch to indicate the mid point between the individual punches is on the handle that you depress to make the holes. This makes it 50mm from the bottom of the paper stack, and then it moves away from the paper stack as you punch the holes. Why not put the notch on the metal that does not move directly above the paper? Not a success

Superb hole punch, can do so many multiple sheets at once. Well made and great for heavy duty work.

I bought this to replace my ageing Velos Perforex 340 which sticks mid punch when punching large volumes of paper and wont release the paper. In all honesty I have gone back to using my Velos for everyday use as this new one just doesn't feel as good when using. Its harder to get the holes straight against the edge of the paper as you cant see through the top of the punch (you can on others and this makes a lot of difference).Also the paper size guild is flimsy and bends. When it arrived there were loads of scratches on the grey metal coating that go right through to bare metal. Would I buy another? No, I don't think I would.

solid no frills pressed steel design

I'm so glad that I bought this. It's especially handy for punching holes in thick piles of photocopied work for the students, instead of doing them in batches. Heavy, sturdy and adjustable (A4, 8x11, etc.) I know that it will last a long time.

Seems to do the job adequately. But a different design has been sent than pictured.

分厚い資料もあっというまに穴があきます。

使いづらい

いいです。ドリル教材をファイルするのに使用してます。表紙があると流石に穴が開かない為、 表紙と中身を別に穴開けしてます。パンチごみ蓋が少々ゆるく。1回勝手に外れてゴミが床に散らばりました(笑) ゴミが一杯な時は迂闊に片手で持ち上げない様に気をつけた方がいいかと思われます。 あと、サイズ表記は少し分かりにくかったです。それぞれのサイズが複数記載あり、初めは「どれだ？」 となりました。でも感覚で位置を覚え、使用しています。 一番分からなかったのは、使用し始めの本体ロック。左に結構力を入れスライドさせると使用出来る様になります。

サイズに合わせて動く支え板が貧弱です。少ない枚数では穴を開けずらいですね。これは厚い（枚数の多い）ものを開けるのによいパンチですよ。

必要充分でなお且つ安いです