BIQU CryoGrip Pro Glacier Panda Build Plate for Bambu-Lab 3D Printers

I picked up this BIQU CryoGrip Pro Glacier Panda Build Plate for my Bambu Lab A1 Mini printer, and it is easily one of the most amazing surface upgrades I have ever deployed [On Wed, June 03, 2026 @ 09:02 AM]. If you are tired of dealing with warped corners on wide-footprint PLA prints, or sick of scrubbing messy glue stick residue off your factory sheets, this specialized "Glacier" formulation completely changes the game for compact machines. Why this CryoGrip plate is a total masterpiece: Unrivaled Room-Temp Cold Adhesion: The proprietary chemical formulation on this sheet is incredibly tacky. I ran a series of dense structural models with my heated bed set to just 25°C–30°C (essentially room temperature). The filament anchors down with massive initial grab force, making first-layer corner lifting completely impossible [On Wed, April 29, 2026 @ 15:24 PM]. Massive Workflow and Power Efficiency: Because your machine no longer needs to wait several minutes to heat a heavy aluminum bed up to 60°C for every project, print runs start almost instantaneously. This dramatically speeds up rapid prototyping timelines and slashes long-term workshop power consumption. Beautiful Fine-Textured Matte Bottom Finish: Unlike the harsh, aggressive texture left by basic stock PEI sheets, the double-sided Glacier surface leaves an incredibly clean, fine matte pattern on the bottom layer of your parts. It does a phenomenal job of scattering light to completely mask visible infill path lines, leaving models looking injection-molded. Perfect Factory Alignment Constraints: At exactly 184x184mm, the plate slips cleanly into the A1 Mini's indexing rear pins. The nozzle-cleaning rear tab cutout is perfectly aligned, ensuring the toolhead calibration sequence doesn't scrape or hang up on the edges of the spring steel sheet. Crucial Setup & Handling Guidelines: Let It Cool Fully Before Flexing: This plate holds onto warm plastic with an iron grip. To protect the specialized chemical coating from bubbling or tearing away from the steel core, always let the plate drop fully down to room temperature. Once cooled, give the spring steel a gentle twist, and your parts will pop free effortlessly. The Freezer Trick: If you are printing a highly rigid or stubborn material that refuses to drop its grip, slide the entire flexible steel plate into your kitchen freezer for 5 minutes. The rapid thermal shock will force the plastic to safely pop loose on its own. Strict Maintenance Warning: Never wipe or wash this plate with harsh chemical solvents like Acetone, which will instantly strip the low-temperature coating right off the sheet. To refresh the extreme tackiness, a simple wash under the sink with warm water and basic dish soap is all it takes. The final takeaway: The BIQU Glacier Panda plate is a premier quality-of-life hardware upgrade that completely lives up to the hype. It eliminates the mess of adhesives entirely, boosts your daily output speeds, and provides ironclad first-layer reliability for a very reasonable price point. It has completely modernized my compact printing environment.

This build plate has made a noticeable difference in my 3D printing experience. Adhesion is much more consistent compared to the stock surface, and prints stay firmly in place during printing without lifting or warping. Once the bed cools down, parts release easily without needing force, which helps avoid damage to prints or the surface. The double-sided texture is a nice bonus, giving flexibility depending on the type of finish you want on the bottom of your prints. It feels durable and well-made, and it fits my printer perfectly without any modifications. So far, it’s handled multiple prints very reliably, even with larger models. Overall, this is a solid upgrade for anyone looking to improve print adhesion and make bed removal easier and more consistent.

I have a Prusa Core One and a MK3.5. Us the on the Core ONe to do oversized prints and it works great. Adhesion is very very good, almost better than you'd want, but you won't have to worry about a print popping off the build plate after that first layer. TIP: do yourself a favor while you're waiting to get this steel sheet delivered. Go to an auto parts store (Autozone for me) and get a plastic scraper that has the changeable plastic "razor blades" in it. Mine is grey with orange blades and my older one is blue with orange blades. They'll be in the aisle with the sealants and adhesives and fasteners or just get it on Amazon. Search for "plastic razor blade scraper" and there are a blue million hits.

I have two kobra 3s and one of them had a z-axis calibration issue which caused it to remove all of the top textured of the original build plate in a 2" diameter circle, so I needed a replacement build plate. I had been reading about the cool plates so I decided to try this one (CryoGrip Pro Glacier). I was really interested in not having to use any sort of bed adhesive, like glue sticks. I hate having to remove the glue stick residue from the prints, it's not hard, it's just a pain. When this build plate arrived, I immediately put it on the printer and printed a benchy, because it's fast and I knew what to expect from the printer. It printed great, no bed adhesion issues. I've used this plate daily for almost a month and I have not had a single print failure due to a bed adhesion issue. The models just stick to it. As a matter of fact, they stick almost too well to it; I've had to start using a metal scraper to remove some models (gently of course). According to the instructions, the bed temperature should be between 45 and 55 degrees C for PLA and the default temp for pla on the kobra 3 is 60. It's easy to adjust the bed temp on the kobra 3 and I have managed to change the default temp to 45; however, the default doesn't stay at 45 for more than 3-4 prints before it's somehow back to 60. So I just try to make sure it gets changed to 45 every time. However, sometimes I miss it and the temp isn't adjusted the bed temp is 60 the whole time, I haven't found that has had any impact on the quality of the prints. This plate is textured, however, it is finely textured, it's not quite smooth but it's pretty close. There is a very noticeable difference between the feel of models printed on it versus those printed on the textured plates. I'm very happy with this plate. I actually ordered a second one about two weeks after I ordered the first one. These are now my go to build plates.

I 3D print daily for my business. There is nothing worse than waking up and seeing a ball of plastic string dancing around your print bed or just as bad, spend several minutes trying to remove a print. After seeing several of these plates around the 3D printing community with great results I decided to give it a try. They are in the mid-level price range but it is well worth it! They are very durable, easy to clean and the build plate coating is quality. I have been using ASA filament and when it cools down for a minute or two, it pops off clean. I immediately bought another plate for my other machine after using it the first day. Don't waste time with other bargain plates; not worth the headaches!

Works pretty good. Fits the FlashForge AD5M / Adventurer 5M. Seems best suited for PLA and ABS. Stickier filaments such as PETG or TPU adhere too well and will likely damage the plate very quickly. Prints do NOT automatically release from this plate like they do with a powder coat textured PEI sheet or a smooth PEI sheet. It is more like BuildTak or what came with the Ender 3. It's still best to heat your bed up but you can use much lower temperatures. PLA will print no problem with no heating, ABS will print okay at 90° rather than 110° This would be great for use with: PLA, ABS, ASA, HIPS, Nylon, Polycarbonate. I wouldn't necessarily use this with: PETG, PCTG, TPU, TPE, Polypropylene

Sometimes sticks too well on PLA. I have both the glacier and frostbite. Frostbite supposedly has better adhesion than the glacier, but I feel like it is easier to take prints off the frostbite compared to the glacier. I enjoy using the glacier more due to PETG just releases once it's cool and you can use alcohol to clean the plate unlike the frostbite where it is soap only.

Bought 4 for my U1 farm. Strong grip, fewer failed prints, worth it. I run a small print farm with Snapmaker U1s and grabbed four of these after the first one proved itself. Mostly PLA and PETG production work, plates in constant rotation. What sold me is simple: first layers just stick. On a tool-changer, a blown first layer wastes a lot more than filament, and since switching to these my failure rate has dropped noticeably. Less coming back to a spaghetti bowl, less babysitting, more prints that just finish. That reliability is the whole reason I bought three more. The grip is genuinely strong even at low bed temps, so I'm not cranking heat to hold parts down, which is easier on power when you've got several machines running at once. They seat flat on the U1, the magnetic hold is solid with no shifting, and being double-sided means four plates is really eight usable surfaces. Great for continuous printing. The honest tradeoff: PLA and PETG grip so well they can be a pain to pop off. Smaller parts and big flat first layers especially. Two things fix most of it. Let the plate cool completely before you pull anything (don't yank a warm part), and dial your bed temp down a bit, because running hot makes the grip worse. If something's really welded on, a few minutes with the whole plate in the freezer releases it every time. Once you build those habits into your workflow it's a non-issue. Docking a star only because strong grip and hard removal are the same coin. It's the feature and the minor annoyance at once. Everything else has been exactly what I want from a farm plate: consistent, flat, reliable, and fewer failures across all four. If you print mostly PLA or PETG on a U1 and you value print success over easy part removal, these are an easy recommend. If you print tiny delicate parts you need to lift off gently and often, get used to cooling before removal and cooler bed temps first. For me, buying four says it all.

本アイテムは、プリントの定着率及び消費電力削減目的で購入。 使用するプリンターはA1mini。定着率は完璧、ベッドの設定温度も低くなり確実に電力消費量を減らせています。

失敗が減った