KMA3700 Accu-Cut XL - Universal Track Saw Guide System - Cuts up to 100" Long - No Clamps Needed - Make Straight, Cross, Rip & Angled Cuts Easily - Circular Saw Guide - Woodworking Tool

Worth the hype. We are thrilled at how well this works and has become a critical part of our construction toolkit. Awesome for when you dont have easy access to a table saw

So much easier than getting that first plywood cut on a table say, even with help. The zero clearance edge makes set up fast. I don't even draw a line, just two measured dots and set the edge there. Drew a line and flipped it around for a second line to check the straightness in it as off 1/32 at the middle. Nice. It actually does stay put without clamps like the video. The aux clamps might be nice as the rubber ages, but so far so good. I store it in 4' sections on it's own shelf. The 4' length still stays put for those plywood cuts.

The Kreg Accu-Cut works better than expected. I get clean cuts of plywood with no splintering and perfectly straight cuts. This is a great addition to my cutting tools.

Pretty good. Can use some Drawer tape to get the slide to snug-up to the rails, once this is done you get VERY straight cuts. YouTube Videos are out there showing the process. Trimmed out windows with it, zero gaps. Would recommend.

I am SO glad I bought this track. Building cabinets I finally have highly accurate cuts across long sheets. Many complain about 1.) sled slop/wobble, and 2.) track alignment. 1.) add a thin strip of low friction tape ($5 on amazon for 5 yards) to the sides of the channels on the bottom of the sled where it makes contact with the track. Instant no slop smooth movement. 2.) align with a quality aluminum 6ft level. Have another person help hold the track pieces tight to the straight edge while you tighten the set screws. You really need a third hand for this, & it turns out perfect with no issues. Slightest amount of loosness while screwing set screws will result in a small gap & inaccuracy, I do wish the set screws used an Allen wrench instead of philips screwdriver, but use a#1 size Phillips & you won’t have an issue. Great track, so happy with it!

I bought this because I couldn’t afford a table saw. But WOW. This is so much safer than fussing around with a sheet of 4’x8’ plywood on the deck of a table saw. It doesn’t fill all the needs so I did eventually get a table saw This is a quality tool. A lot less expensive than a Festool which we used at work. Pretty much just as good. So get it. Get enough pieces to do the work. Label the underside of each. Find a create a safe place while not in use. I paired it with a Makita 8” radial saw. And a really nice blade.

Makes cutting full sheets of plywood easier and eliminates the need for expensive table saw

Got a great deal and used my points to sweeten the deal more! Arrived the next day, exactly as described!

Had quite a few 4 x 8 ft sheets of OSB to cut up, and this made it much easier and a lot more accurate. My Evolution circular saw fitted perfectly. Nice and easy to set up and use.

Rectifico que si trae la mica y por eso le doy 5 estrellas

自作も含めいろんなガイドを試しましたが、その度に満足のいかない結果に残念な思いをしてきました。 どんな道具にも使いこなすにはコツが必要で、しかしそれを習得する前に丸のこを使うのが億劫になっていました。 ところがこのアキュカットは、そんな私でも一発でコンパネの長挽きに成功。丸のこを使うのが楽しくなりました。 唯一越えるべきハードルは、説明書が英文だということ。でもそれはスマホに入力すれば和訳してくれます。そうやって地道に説明文と向きあうことで、より商品が理解できるというもの。 おすすめです。

Super produit très utiles et rapide à monter expédition plus vite que prévue content en tout je le recommande

Definitely a bit fiddley to set up. But worth the time! Once I had my saw set correctly the track works very well and helps make accurate, long cuts quickly. No need to draw a line. Just mark the beginning and end of the line, drop the track onto your sheet and push the stop up against the edge of the sheet. Then make the cut. (I'm using a DeWalt 20v circular saw). I was very impressed how I was able to easily make angled cuts on a sheet and it didn't slide around! I bought the accessory clamps but haven't used them yet. They would add a minute to set up the cut but I haven't felt like I needed them. The Kreg track is really handy and I can see that I'll stop using my table saw for cutting sheets now and just use the track.