DYMO Embossing Label Maker with 3 DYMO Label Tapes Organizer Xpress Pro Starter Kit Ergonomic Design For Home DIY & Crafting

Originally, I was having major issues with this (not cutting, not writing any letters) like some others have posted. But after some troubleshooting I noticed that the arrows along the wheel were not aligned. The two top arrows should point directly above the two bottom arrows. I'm not sure if it arrived this way, but as soon as I adjusted this it started working

Es perfecto la cinta es muy buena la tengo en productos q les cae agua constantemente y no se despegan. Si les encanta como a mi la organización comprenlo no se despega por nada del mundo

This label maker worked very well at the beginning, for about an entire roll (photo of red label as an example). I managed to label everything I needed and wanted to, so that's good. But now it just messes up every time I try to create a label. The letters don't get embossed, and if they do, they're out of alignment (see the photos with the black labels). I don't know, maybe it's because I was squeezing the trigger to hard or something. Or maybe there's a piece of debris stuck in the mechanism. I think I'm just gonna spend a little more for an electronic label maker next time.Update: I managed to fix my Dymo labeler. It's not because I was pressing too hard. It's because it's badly designed with cheap parts. I'll explain. You have to remove the two screws at the bottom and then remove the entire "head" of the device (the rotating cassette of letters). It'll be tricky, and you'll have to slightly pry the handle apart a little bit, but it can be done. Inside, you'll find the little plastic hammer that pushes up against the letters. Every time you squeeze the trigger, the little plastic hammer pushes up against a letter to stamp your label. Now, each of the letter stamping pieces is not a solid piece. It's hollow with a cross brace inside of it - and it's sharp. The reason why this thing fails after a certain amount of use is because every time the hammer makes contact with a letter stamping piece, it pushes up against the cross brace and the edges of that letter piece, and because that hammer is just malleable plastic, it WILL get dented and deformed (see my "deformed plastic hammer" pic). Then with every squeeze of the trigger, the plastic hammer will deform more and more until it no longer pushes evenly against the letter, and the letter stamping pieces basically just slip off of the hammer pushing up against it. This is why it stops stamping letters properly, and why sometimes the letters are out of alignment.To fix this, you'll need to fix the plastic hammer. I personally filed down the chipped and dented head and then attached a tiny piece of rubber to it. Make sure that whatever you're attaching to the hammer is thin enough though. The cassette of letters still need to freely rotate above it. But as you can see in my example pic, it's all fixed again.So, it works again, and the labels are all coming out correctly again, but I'm still giving this thing two stars because it's built very poorly. I would've given it a one-star, but when it works, it's cool, and it's at least easy-ish to fix. But I shouldn't need to crack this thing open and MacGyver a fix for it. The letter pieces should've been solid pieces instead of being hollow and having that sharp bracing support in it that damages the plastic hammer. The plastic hammer should've had a rubber or metal piece on the tip to reinforce it and prevent it from being damaged. Sure, this thing will probably work for you through an entire roll, maybe two, before it fails - and it WILL fail. But unless you're comfortable with fixing this thing when it does break, I'd seriously consider something else.2022-03-27 Update:My fix to print letters is still working, but the cutting blade on this label maker has completely dulled, and I still have another roll left. It doesn't cut anymore, and I didn't even go through two rolls! This product is terrible. I'm knocking it down to 1/5 stars. If you want a long-lasting label maker, go look elsewhere and don't cheap out. This thing sucks. Cheap materials destined for the landfill!

Great! this is an awesome product for cheep! But just to let everyone know, to get the best experience, always go clockwise not counterclockwise.you can use it counter clockwise but for some reason, it messes things up a bit and you might get a little bit weird prints.but other than that, it’s such a great product to label everything. would recommend.

I had a little bit of trouble with this at first but quickly figured it out after about 45 minutes of continual testing.I noticed a lot of people with this product seemed to be complaining about the striking and clarity/readability of this and the amount of pressure it took.From my experience so far with this device1. super easy to reload and change out colors2. when first starting use a double or triple trigger pull on the space button ( ___ ) , it'll give you a little bit of slack to start with. you can keep it or trim it later.3. when you first get it, I would reconmend going around to all the digit options and press and hold the trigger pretty hard. do this a few times and then you can relax.4. start using it, you should be able to do quick punches with little to not effort and get clear words, sometimes a letter can come out faint if you really are too light with it or if you're slightly off the mark from the letter5. the cutter is great but short words and sometimes just regular or long ones seem to be stuck in the feeder out, but they just need a little tap or pull to come out. Tweezers from my vinyl cutting kit worked well, i'm sure any tweezers would6. for the price of this, its super awesomeDownsides1. little to no instructions2. starts you off with just a small amount of "tape"3. doesn't have a clear engagement marking for which letter or character you are pressing, just a click that lets you know you should be in the right spot4. can take a while for long words, might upgrade in the future

I loved this labeler, very useful for whatever you want to mark.

I was really excited for this label maker and it worked great when I first got it. Im right out of the 30 day return period & now it won’t work. I used it as directed and I haven’t even gone through the first role of black label tape that it came loaded with… I think the discs with the embossing mechanics separated and now it won’t emboss anything or cut the tape… I’m very sad…it’s basically useless now…UPDATE! After leaving my review I went hunting through others to see if anyone came up with a solution. Apparently these two arrows are supposed to be aligned. Once I realized it I got it to work again. So if you have a similar issue with yours, realigning these arrows may fix it. 🖤I left my review at a solid 3 stars. I don’t know how long this will fix the problem and it kind of sucks that it becomes unaligned so easily but it still does the job I guess and it is easily fixable.

Even though this is old school tech, these labels last longer and stick better than the newer versions.