ledmo LED Strip Lights, Non-Waterproof LED Strip DC 12V 16.4Ft White 6000K 15Lm/LED High CRI80 COB LED Light Strips for Mirror, Kitchen Cabinet, Bedroom

These little bright lights turned a couple of dark cave like rooms into bright living spots--I can't say living room bc these pictures were our bedroom, although the lights are also in a combined living/dining room. Also around a counter in a store making another level of versatility and positive point.I bought the cool white bc I needed to be able to read in these rooms so I use a remote to vary the brightness. These lights can go from task/reading lights to mood lighting easily. NICE.Pictures show these lights above the crown moulding. These are small enough to not be noticed immediately but still quite useful bc the level of brightness goes up allot.I do wish the adhesive was stronger bc in each application I've had to reenforce with a separately applied tape.The light strip is flexible, goes into a corner, around a curve and flat surface.Yes will be buying these again bc next they are going into the RV.All said I guess I just do Not like cave dwellings hence my purchase of several rolls of these little bright lights. Also buy some contact cement to assist with adhesion.

Finally found led's that are the SAME color temperture all around. I've went through about 30 rolls of strips from different companies and all were diff color temperature but these from ledmo are amazing. If you need led's that are same color temp all around for sensitive lighting fixtures then these are for you!! So happy. No idea how much money I spent looking for evenly lit led's. Basically trial and error with the messed up amazonlisting. Btw if anyone here is going to use these for lighting a film set or for putting on makeup then keep reading. In-camera they give off a violet hue that can be fixed with color correction but it's going to be a very tedious process. If you want led's that are good for filming then you'll need ones that have a high CRI number and those are SUPER expensive and not worth it if you're not a professional film-maker with a huge budget. Otherwise, just get these. Superior quality over other led's on amazon and they don't cost more. Win-win.

I needed to cut this into 5 one meter strips. I had to use the clamp on connectors. This is not easily done. The waterproofing layer must first be peeled of for about a half an inch or so. Then you must remove the adhesive coating on the other side. This is not easily done. I used a pocket knife to careful scrape about a half inch off. You must do all this for the connector to work. The adhesive prevents it from sliding into place. So you are forced to remove it. When I was done all the leds lit up and all was well. This is an initial review. I have only had them a few days. I gave it four stars because I like how much light it produces. I used my own 12 volt linear power supply. The leds were so bright I worried about how long they would last. I checked my power supply and it was putting out 14 volts. Luckily I found an adjustment potentiometer inside the power supply on the PCB. I adjusted it to 12 volts. This reduced the brightness but is far better than burning them out early. Others have complained about the waterproofing turning colour. I think I will carefully remove this coating before installing any more of these lights. The adhesive does work pretty well. It is very sticky. If you have no intention of cutting the strips, your installation will be much easier than mine. Make sure your power supply is not over 12 volts. The life of the LEDs is seriously shortened by causing current beyond specifications of the LEDs. Actually, it is exponentially shortened as the voltage and current increased. This would be true of all LEDs. Also, be very careful about removing the paper cover over the adhesive. Sometimes the adhesive layer comes up with the paper. Carefully separate them if this happens and put back the adhesive and all will be well. I recommend using a sharp knife to carefully separate the paper from the adhesive initially. Then you can safely pull the rest of the paper off. Before arbitrarily pulling off all the paper, test the light strip back side to make sure the first inch or two you have exposed is sticky. If you are pulling off adhesive the strip will not be sticky at all. I wish you a good installation

I used these to replace the CCT lighting in an older monitor that had lost its backlight. They were exactly the same width as the CCT tubes so they fit right into place. I was worried that the gaps between the LEDs would end up being visible through the diffuser but once I got everything back together, it looked great.They aren't _quite_ as bright as the CCT they replaced but they're awfully close. More importantly, they have even/consistent color temp so there's no yellowing or blueing across the picture.They generate a little bit of heat at 12v but nothing extreme. I'm VERY happy with this strip and will be using it in more CCT/CFL replacements.

I bought these to install in my truck bed, the double sided tape would work well for a hard flat surface but my truck has a spray in bed liner so to be safe I used some more heavy duty adhesive for my application. These led's are bright white! Not a soft white or yellow but bright white which is great and exactly what I wanted. I didn't use the power adapter ends that are pretty wired because of my application but that would be handy if you were using these for under cabinet lighting or something similar. All in all they are great and at a great price! Definitely recommend and worth the money!

These lights do work and have a bluish cast to the light, which was anticipated. Light out put was less than expected. It took 4 16" strips to approximate the output of two 14w florescent bulbs and the florescent bulbs still produced greater defused light. Silicone coating on tip makes use of paired quick connectors unusable. I ended up having to cut back the silicone and soldering the connections. Most disappointing was the adhesive backing. Applying to clean dry metal the adhesive on 50% of the strips failed requiring the fixtures to be taken down and the strips hot glued in place. I would not buy this brand again.