GE Appliances WB13K21 Genuine OEM Burner Igniter for Ranges

Worked as it should and fixed our oven baking issue. It was delivered quickly. It’s an oem part. So build quality should be really good hopefully. Only time will tell with it. But in theory using Oem grade parts usually hold up better. And it’s only about 6-9 dollars more than the no name third party appliance part brands.

Works well. The ceramic twist ons were better sized then on the generic brand I tried installing previously.

Igniter works as it should in my over 20 year old Kenmore gas range ( model 362.75271691). I did have to clip off the included plug and direct wire using the wire nuts. The old igniter did glow but the oven would not light so I wasn't 100% sure the igniter was the issue. After a little research it seems igniters can still glow and appear visually to be working but in reality it isn't pulling enough power to fire up the gas. This fixed the problem. Installation is easy, just removed the drawer and reached in to replace it. You just have to be willing to lay on the floor! I can't speak to longevity having only installed this a week ago but at the price i might just order another to have a backup.

Not a genuine GE part

Fits great, works great. It had the correct connector, I did not need to splice any wires. Plug and play. It was nice that they included ceramic wire nuts if the connector is different.

The OEM part arrived promptly and works great in my GE Profile oven. It was the best price I could find. If the GE help desk had knowledgeable people I would have replaced it months ago (2 separate calls to them proved worthless). I finally diagnosed the problem by searching youtube. Unfortunately, one of the screws that held in the old igniter was not only installed on an angle, but it was actually bent. I had to finally hacksaw the screw off from both sides, coax the remaining seized section out of the hole, and then re-tap the hole. I was fortunate to find a screw in the workroom that would fit, with only minor modification. The good news is that the oven now hits 350 degrees in a little over 7 mins. But, so much for a 20 minute job... It is now 3 years later and this part had to be replaced again. I don't think it should have crapped out that quickly. But for the price I got it from Amazon for, and what GE wants for it, you can buy almost 4 of them. Still, for its longevity, I knocked the review down to 4 stars. This is also the same part for the broiler in my range too. I just replaced that one today for the first time. As an FYI to anyone also replacing it for the first time in a range like mine, I discovered you have to pull the range out and take off a cover from the back because the wires are held in with a clip from behind. I'm glad I stopped yanking on the wires when I did and took the time to investigate from the back. Who knew?

This igniter, GE Part Number WB13K21 is made by GE in the USA and a direct replacement for the original igniter part number WB13K00021 used in my 2005 GE Profile Range, Model Number JGB915SEF3SS. It is of very high quality. It is packaged well. It is a drop-in replacement. My igniter would glow red hot but the the gas valve would not open for the flame to ignite. My range still worked and my broiler still worked. If I had a current meter I would have been able to measure the current draw and would have found it to be below the necessary threshold to allow for the gas valve to safely open. This item is easy to replace, only needing about 30 minutes of time, a 1/4-inch wrench and flat-head screw driver. These fail from normal wear and tear. There are plenty online videos demonstrating the repair.

I read some reviews about the oven not kicking on and smelling some gas when turning on the broiler. I had the same experience, but then I realized that it was completely my fault. When you install this item, you want to make sure that the part that is shaped in an angle is the part that needs to be fixed near the flame, facing the flame directly, otherwise the gas will just keep going without any ignition happening. Now, as soon as the gas starts flowing, it instantly turns on which is awesome. So far so good

It is an original product by GE, the packaging indicates that very loudly. It's a bit more expensive than the other non-original parts but I was fine with it. As soon as I replaced the old igniter with this one, the oven came back to life! My only complain is that the wires on this part is shorter than of my original one the oven. I had to take a shortcut and pass the wires through a route that was not designed for it. But overall happy that I was able to fix my oven without paying a few hundred dollars to have it fixed.

Working perfectly and also came with 2 ceramic wire connectors , you need those. 👍

Works as expected. Got rid of the burning smell the old one was emitting.

Thanksgiving day, and my oven failed. The gas wouldn’t ignite. Of course it would happen when I wanted to roast a turkey. After checking our model number and carefully looking online, we were able to order a new igniter. I cooked my turkey on the bbq. A couple of days later, the new igniter was delivered. My husband is a very handy guy, and was able to install this and we were back up and cooking within half an hour after delivery. Fantastic! Saved our stove from the landfill, for only $60 bucks. Very happy cook here! Thanks Amazon!

Bought for ge cafe series, could get genuine parts for months, works great, easy to install