3-3/8" (85mm)-30T, Metal Working Circular Saw Blade, Arbor 15mm with 10mm Wahser, Use on All Brand 15mm Arbor Cordless Saw, Metal, Steel Iron Bar, Sheet, Angle Cutting

Bought it to cut tin for my pole barn. Used it in my Ryobi plunge saw. Cut the tin with ease .

Buen corte,en las tuberias de emt

The LSHUZIYU 3-3/8" (85mm)-30T, Metal Working Circular Saw Blade is advertised "Use on All Brand", but as two of my pictures show, the outside diameter of the blade exceeds the capabilities of my saw. When I noticed the problem I measured the diameter of the blades that came with my saw (3"). Then I measured the distance from the center of the spindle to the furthest point inside the blade cover and found I needed a blade no larger than 83mm/ 3.25" (almost an eighth of an inch smaller in diameter than what I received, 85mm/ 3.35"). I didn't see the blade diameter specification in the saw's box when I ordered the blade (I eventually located that information on a side-panel). So, shame on me for thinking "small" circular blades are of a "universal" dimension (except for the center hole, of course) when I read "Use on All Brand" in the advertisement. I really did "assume"..... However, I *WILL* commend the company on it's EXCELLENT packaging. It's easy to open - but almost impossible for that to happen accidentally. It also protects the product from damage in normal - and maybe even more abusive than normal - shipping. Once the box is opened there are three tabs that hold the blade in place, used to prevent the blade from sliding around inside the box. After bending the cardboard tabs out of the way, then I could lift the bag which contained the blade and the sizing spacer-washer ("wahser" as used in the informational paragraphs describing the blade) which is used to accommodate various motor spindle diameters (which too aren't "universal", apparently because my saw uses 7/16ths of an inch, not 5/8" or 3/8" - the sizes of the spacer-washer). The edges of the blade are further protected with a vinyl sleeve that once removed, exposes the blade's "teeth" - which are VERY sharp. This product appears to be made with attention to detail, seems to be of high quality and packaged well. I am disappointed it didn't fit my saw, and disappointed again, that I couldn't present its use in a video.

This blade came in a box to protect it from getting bent. That was very nice and sharp worked beautifully.

At first this thing cut like warm knife through warm butter. However within about thirty seconds the honey moon was over. It started slipping and balling down the motor to where it wouldn't cut anything. I've never had an issue with the saw until using this blade. My 2 minute job turned into 15 minutes of pure pain in the rear. I ended up using another cutting blade with much better results.

This item is small. Yes, the description says "3 3/8", which is accurate, but I guess I didn't realize just how small that would be: it's about the size of the palm of my hand (I'm about 5'8" and my hands are neither huge nor tiny). It actually fits fine on my cordless Ryobi circular saw: you can still lower the blade enough to clear the base and take a cut. I plan to use this to simply score metal for bending rather than do any heavy duty cutting; I have not yet had a chance to try this. The brazing on the teeth looks good so I'm not anticipating any problems unless it's that my cordless doesn't have the oompf to cut, but that would likely be more on the saw than the blade Will report back if the blade doesn't hold up to use, but certainly looks reasonable.

This 3-3/8" diameter blade has 30 carbide teeth and is rated for 7,000 RPM while cutting metals (iron, steel, aluminum and copper). It is ideal for use with most cordless circular trim saws. The blade leaves a thin kerf to minimize material wastage and has laser cuttings to ensure dynamic balance. I used this blade to cut a series of cuts on 3/16" x 2" x 2" aluminum angle iron. There were no problems and the blade seemed to retain sharpenss while leaving smooth cut surfaces that required minimal post cut touch ups. Would recommend this for all those looking for a high quality product.

Nice little blade that will rip through what you need it to. You will have to do a little touch up afterwards but that should be expected. Have used it several times and have not seen a change in performance yet.

El espesor de la hoja es de 1,25 mm, mientras que la de Bosch es de 0.8 mm. El corte de perfiles de aluminio ha sido limpio y fácil. Sin calentamiento de la hoja. Su rigidez ofrece la tranquilidad de no tener atascos peligrosos. Los cortes son limpios, sin astillas. Incluye una anilla de centrado para reducir el eje de 15 a 10 mm.

Als Sägeblatt für eine kleine Bosch (Holz) Kreissäge. Schneidet 0,6 mm V4A Edelstahlblech sauber und mühelos. Habe ein Nadelholzbrett drunter geklemmt und die Schnitttiefe auf 3mm eingestellt. Kaum Grad, kein Funkenflug und ein sauberer Schnitt ohne den ganzen Staub einer standard Trennschleifscheibe.

Very sharp and good price

The build quality is much better than an average circular saw blade, very refined and well-cut. As this is for ferric type of metal, the tooth profile has the anti-kickback design. In order to use it for metal properly, people easily miss the importance of speed, temperature and pressure applied. It's not suitable for most of angle grinders. For instance my tiny Bosh 12V battery grinder/cutter, the speed is twice as what this blade specified. It can also be dangerous as the blade profile is not safe for the application . For angle grinder type, should use much higher number of teeth with a forward and reverse symmetric profile. Or abrasive type of cutting discs. When cutting, the pressure should be as gentle as possible and spraying oil to the cutting point may also be helpful. I use this blade mainly on a mini drop saw and a mini table saw. Both have 10 mm arbor so I made up a special 15mm to 10 mm adapter for it. The supplied adapter will not fit as the 10 mm shaft backing is only 15.8 mm in diameter.

Bald3 was tested and worked great as per my husband