Paintless Dent Repair Kit, Small Dent Removal Kit, Dent Removing Tool with 33 Strong Pull Tabs Suitable for repairing 0.6'' to 8'' Car Hail Damage and Door Dings

This dent removal kit comes in handy! It’s suitable for beginners and works well for minor repairs. I’m satisfied with the comprehensive set of tools that It comes with alongside instructions which are there to guide.

GREAT starter kit. I did not buy the more expensive kit because the light board in it had bad reviews. I purchased a light board separately and already had a hammer puller. Both items are very useful. The worst part about this kit are the directions, which are worthless. Spend an hour or two on the internet / YouTube to learn about PDR and how to use the items in the kit. Pay particular attention to how to use the glue. How you put it on, how much to put on and how long to let it sit before pulling are key. But even more important is which glue to use. In a 60 degree garage the yellow glue worked very well for me, but the black glue was just a mess. I have had mixed success with this kit on an old car that my children drive to school. It has a large variety of dents from superficial to demolition derby worthy. The small and medium dents are already fixed. The deep gashes and dents that have creased details in the hood, doors and edges of the wheel wells are giving me more trouble, but I am learning. I have found patience is the key. I will update this review with pictures of my car after I make all the mistakes on the car that seems to get a new dent once a day at the high school.

The metal tools are well made and work well, but the glue sticks are useless. They stick like heck to the car but not to the plastic pulling tabs. The pulling tabs are also super flimsy so they kind of buckle and tear away from the glue at the middle rather than pulling evenly.Get the one from east wood company.I just ordered the monster red glue sticks on Amazon for another $25 and I'm looking for better tabs.

I had a dime sized dent in my car. I was a little skeptical if this would work on it. Luckily it comes with tons of accessories and pieces that fit the size of the dent. I tried both the yellow and black glue stick. The yellow is the strong of the two. It took about ten different attempts to get it where I wanted it. It's still not a 100% better, but the size of the dent is roughly 1/4 of the original size. I may try it again to see if I can get the rest of it, but to be honest I didn't have high hopes this would work at all. The dent looks much better than it did.

Very hard to use.

Received order fast, reviewed the instructions book at came with it. Very straightforward. I was able to remove a dent on the roof of my truck with ease. But it does take multiple tries, don't think you will get it one. I would recommend for small dings and dents

This is a good product that works if you follow the instructions and are patient. It can be tedious and sometimes takes multiple attempts to get a dent pulled out. It gets easier and faster once you get the feel for it. I just make sure I clean the surface good, use the black glue sticks ( purchased extra on Amazon for 10 bucks), have plenty of light ( I wear a headband light), use the hand held puller, then get down at eye level as I’m pulling. Sometimes I pull gradually, then let off, and pull again. You can kind of see how much u are pulling it out as you go. It’s not like there was never a dent, but you can get it out enough so you really don’t notice it. Better than spending thousands at a body shop in my opinion.

The glue doesn't hold well enough to provide enough pull power. I have a 3" diameter dent that isn't creased and perfectly round in my truck bumper. This should have been an easy dent to pull but after many attempts and over an hour I finally gave up. I went through all three black glue sticks and the glue stuck to the metal bumper much better than it did the pads that come with the kit. I even soaked the pads in isopropyl alcohol for 3 hours before using them as the instructions recommended. Eventually I used some sand paper to rough up the surface of the pad I was using and the glue was holding much better but this kit doesn't have the pull power to be be effective. It might work on very small dents in thin sheet metal but that's about it.