ChenYang USB 3.0 Front Panel Header 19/20Pin Male to Female 90 Degree Down Angled Mainboard Header Gender Changer Connector Adapter

Exactly what was needed for a much more clean USB 3 header connector installation. A bit on the snug side to install but holds firmly in place. Supports speeds as expected. No complaints!

Just be careful, the blue housing can be somewhat delicate, don't yank the USB3 header cable out of it. Look at videos of how to remove the cable, rocking it back and forth, slowly and gently.Otherwise, this worked perfectly in my build to make the USB3 header cable much less obtrusive.

Bought this to help reduce some cable stress on a tight PC build, and it does the job well enough. I wish it didn't have the blue connector, as a black one would be more incognito, but something like this is meant for function over form. It's also home/hand made, which is fine, but don't expect manufacturer level fit and finish.It connects just fine, and works normally without issue. If you have a tight cable run, or want to streamline things a bit this can help with that.

I have a Mother Board with two USB 3.x headers. Unfortunately, one of them was blocked by a second graphics card that I have installed. Using this device and a small riser for the GPU, I'm using both USB 3 headers. I have what I need and that makes this

This was something I was hoping it was going to work, the USB 3.0 port on my motherboard was sort of in the way if I was to get a longer graphics card, this would’ve fit the bill, the trouble is, the moment you plug it in to the motherboard with the cable, it almost becomes permanently attached to the cable, and as you know these cables they tend to be pretty thick, and depending on where you route it through the cable management holes in your case, there will be some tension on the cable where it connects to the motherboard, now there’s tension on it anyway when it’s in its normal slot, and the motherboard slot has no problem dealing with this, this thing worked maybe five minutes, and that little tension completely killed it. I’m glad I didn’t do any more harm to the computer as some people have mentioned, I noticed that it’s like a pin/Lego/circuit board construction, very flimsy. I wish it was a lot more solid and less likely to fall apart.Great idea. Poorly done

The adapter worked well enough for me however it is a little flimsy, be careful if you need to remove it from either the board or the cable end as it is possible to pull the assembly apart. The color is yuck so style points are down the chute but I wasn't willing to pay 3 or 4 times more for a black plug lol.

I got this to allow a CPU fan not to be bothered with the front panel USB cable, this mostly did the job as it changes the angle from which the cable connects to the motherboard, however the adapter itself is quite tall so my fan still can't fit properly.I have not tried removing it yet so I cannot share anything about the issues I saw in the reviews, and I assume I am familiar enough with hardware handling to find the solution to remove this without damaging the motherboard, however if it turns out to be excessively difficult this would definitely take a star away from it.To be continued, so far so good

Many currently in use motherboards (main boards or logic boards) which sport the Gen 3, Gen 4 quad core Intel processors, but have USB 5.0 front panel connectors, place those connectors near the ram slots. When attempting to install an updated video card, which is 10 inches or so in length, the USB 3.0 slot gets covered over by the video card.If the USB 3.0 slot which provides front panel USB 3.0 is parallel to the ram slots, then this bit can be used to turn the USB connector 90 degrees. where it will clear the bottom of the graphics card and allow the front USB 3.0 to connect. This worked with the Dell 7010 main board with the intel i5 3470 processor and the MIS RX480, 8GB graphics cardif however in the case of the HP 600 G1, the front panel USB 3.0 slot is located 90 degrees to the memory slots so using this option will not work. And the user will simply have to nix having front panel USB 3.0 if they install a long graphics card